Special Instructions - Dupla CO2 Armatur Smart Mode D'emploi

Anschluss eines CO Magnetventil Pro (Art. Nr.: 80243)
2
Für eine halb- oder vollautomatische Regelung besteht die Nachrüstmöglichkeit eines CO
Magnetventils. Das CO Magnetventil Pro wird zwischen Armatur und dem Feinnadelventil
2
geschraubt. Entfernen Sie das Feinnadelventil von der Armatur. Anschließend verbinden Sie das
Feinnadelventil mit der Verbindungsschraube des CO
Montage die Außengewinde der Anschlüsse mit 4 – 5 Lagen Teflonband umwickeln
(im Lieferumfang enthalten), um eine 100 % -ige Dichtigkeit zu garantieren. Anschließend drehen
Sie nun das fertig montierte CO Magnetventil Pro in die Armatur
2
Magnetventil Pro aus und überprüfen Sie die Schraubverbindungen auf Dichtigkeit!
8 9
10 11
Ersatzdichtung:
Art. Nr.: 80212 Flachdichtung CO Armatur Smart
2
Technische Daten:
Manometeranschluss 1 x 1/8 Zoll, Iso 7 (Din 2999)
Ventilspindel: Edelstahl
Anschlüsse: Ausgang für CO - Schlauch
2
Mikrofilter: 2 Stück eingebaut
Material: Messing vernickelt
4
2
1a
Magnetventils Pro 8 . Unbedingt vor der
2
9
10 + 11 . Richten Sie das CO
Gewicht: ca. 670 g
Technische Änderungen vorbehalten.
Abbildungen sind unverbindlich
Flachdichtung CO Armatur Smart
2
(Art.-Nr.: 80212)
CO Armatur Smart
²
Thank you for purchasing the CO
Smart you have purchased a product of the highest quality and reliability. Strict and permanent
quality control as well as manufacture in accordance with ISO 9001 ensure a product with a
long useful life. These instructions are part of the product. They contain important information on
set-up and use. Please keep these operating instructions for further reference.
2
Special features of the CO
· pre-set optimum operating pressure
· thanks to new knurled nuts, very easy connection to the CO
· high regulation accuracy through high-precision bubble count setting
· incl. integrated swing check valve
· water-jet pierced rubber seal for wear-proof seal to cylinder valve
· corrosion resistant thanks to material finishing
· for all CO cylinders with external cylinder valve
2
· integrated overpressure safety valve
· compatible with CO Solenoid Valve Pro (art.-no.: 80243)
2

Special instructions:

Replacing the depot and working on the CO
out in unpressurised state.
Usage / Set-up:
Make sure that the stainless steel fine needle valve
Pressure Regulator Smart to the CO
the opening of the cylinder valve and tighten the union nut
spout of the CO Pressure Regulator Smart
2
tight hose. Completely open the cylinder valve. The pre-set operating pressure of 1.5 bar is shown
on the manometer 5 as the optimum. Then use the adjustment screw
fine needle valve to set the desired bubble count. If the pre-set operating pressure sinks into the
red area marked refill, the CO
Please note: When connecting the CO
move into the yellow "High" area when opening the cylinder. This is normal as the
Pressure Regulator Smart. With the CO
2
Pressure Regulator Smart:
2
cylinder
2
Pressure Regulator Smart should only be carried
2
1 is closed before connecting the CO
Depot (CO cylinder). Place the cylinder connection
2 2
3 . Connect the hose connection
4 and the CO Reactor or CO
2
cylinder needs to be refilled or replaced.
2
cylinder, the pre-set operating pressure may
2
Pressure Regulator
2
2
2 in
Atomiser with a CO
2 2
6 on the stainless steel
5