Bodet PPMS Notice D'installation page 2

This document describes how to implement a S.E.P. (Safety and Emergency
Procedure) with Melodys Sounder.
2 S.E.P. dedicated warning sound signals are generated:
- 1 to indicate the beginning of the alert
- 1 to indicate the end of the alert.
Each signal is controlled by 2 pushbuttons: one «Start» and one «Stop».
3 choices for each warning signal:
- official S.E.P. warning sound signal,
- spoken message,
- warning sound signal and spoken message.
These 3 options are available on the SD card.
The pushbuttons must be installed in a restricted area readily accessible
only to the personnel in charge of the S.E.P. program.
INSTALLATION
Install the 2 "Start/Stop" stations.
Install the "3-input" extension card in the master clock Sigma:
Wall version (fig. 2A): loosen the 2 screws of the front cover, remove the
cover (for the lower half of the cover, push on the clips (N) and slide the
cover upward). Disconnect the ribbon cable (Q) (watch for the orientation
of the connector when pluging it back on) and install the "3-input" extension
card(s) in the locations (X1) (and (X2)).
Rack version (fig. 2B): remove the cover and install the "3-input" extension
card(s) in location (X1) (to (X4)).
With a telephone type cable (AWG24 - 2 km max.) connect the "Start"
pusbuttons of the 2 stations to the first 2 inputs of the "3 external inputs"
card of the Sigma and the 2 "Stop" buttons on the third input of the
extension card (Fig 1).
The equipment must not be powered on until the installation is completed.
SIgMA PARAMETERS SETTINg
After the installation has been completed save the Sigma settings on a USB
flash drive.
Start the Sigma configuration program on you PC.
In the tab "Technician/Installation" select "Allocating option cards". Check
the card number especialy if a Sigma Sound is present in the installation.
Select "Option 3 EXTERNAL inputs" to configure the 3 inputs.
Configure the input A (Beginning of Alert) by setting the mode ON and select
the Melodys and/or Sound module that will broadcast the "Beginning of
Alert" melody of the S.E.P.
Configure the input B (End of Alert) by setting the mode ON and and select
the Melodys and/or Sound module that will broadcast the "End of Alert"
melody of the S.E.P.
Configure the input C (Stop the Alert) by setting the mode OFF.
Turn the card ON (state = ON).
Save the configuration and load it in the master clock with the USB flash
drive.
MELOdyS OPERATION
The Melodys is controlled by the master clock via HF radio signal.
The SD card (ref. 508 474) which contains the 6 S.E.P. mesages must be
inserted in the Melodys (fig. 3)
When the "Start" pushbutton is pressed the master clock sends the radio
signal to the Melodys which plays the selected melody (the melody is
selected by the master clock). Pressing the "Stop" button of the S.E.P.
station turns off the melody.
Everytime a melody is played its number is displayed on the Melodys
control panel (fig. 3).
Implementation of Safety and Emergency
Procedure (S.E.P.) with Melodys Sounder
Check the product for shipping damage on reception for any reservations to the carrier.
FIg. 1 : SyNOPTIC OF A S.E.P INSTALLATION
Beginning of Alert
Start-Stop station
3-input
extension card
End of Alert
Start-Stop station
FIg. 2A : FIg. 2b :
X1 X2
X4
N
Q
FIg. 3 :
X1
BP1 49340 TRÉMENTINES
FRANCE
Tél. 00 33 241 71 72 00
Fax. 00 33 241 71 72 01
www.bodet.com