Cassese CS 59 Manuel Technique page 8

MAINTENANCE
3 ) IN CASE OF HAMMER AND WEDGE JAMMING
AFTER EACH INCIDENT, IF THE HAMMER STAY JAMMED IN BLOCK H,
YOU SHOULD HAVE TO CHANGE IT
WEDGE
DISTRIBUTOR
(BLOCK H)
LOCKING SCREW
- Remove the cartridge that is on machine, and the top presser.
- Using the 3mm Allen key, loosen the locking screw of the wedge distributor Block H.
- Then lift the top presser's bracket arm by hand. The wedge distributor will come out of its
housing.
- Remove it from the machine.
- The old hammer (wedge driver blade) is stuck in the wedge distributor : first try to remove it
with a pair of pliers. If not possible, remove the four screws (A, B, C, D) and open the block
H.
- Remove the old hammer. Assemble the Block H back again.
Putting a new hammer (driver blade) :
- Put a drop of grease in the bottom hole of the wedge distributor (block H).
- Insert a new hammer into block H with the hole of the hammer downwards.
- Re-position the wedge distributor in its housing on the machine with the window towards the
cartridge.
- If the upper end of the hammer stays out of the block H, push it fully in with a piece of wood or
moulding.
While keeping the moulding in place (on block H) and pressing on it, pull up the top presser's
bracket arm Po (Fig1 p1) with a quick movement.
The new hammer must have taken its position in the mechanism automatically.
- Check with your finger that the block H does not stay out of the machine (higher than the work
level) and tighten the locking screw of block H. No need to tighten too much.
- The machine is ready to work again.
If you have any difficulty to remove the block H from the machine, push down with
your hands the top presser's bracket arm.
This should free the block H that is stuck with the hammer.
A
GF1
GF2
B
SCREW
POSITIONS
BLOCK H
11
D
De conception originale, utilisée sur toutes nos assembleuses,
L'agrafe en w brevetée Cassese
Chargement du barillet de la CS 4095
C
A
GRAFES INDEPENDANTES, SANS COLLE, EXEMPTES DE LIANT : PAS D'ENCRASSEMENT MACHINE
L
UBRIFIEES POUR FACILITER
C
ONDITIONNEES EN CHARGEURS
.
I
DENTIFICATION CHARGEURS VERSION
I
DENTIFICATION RAPIDE DES HAUTEURS D'AGRAFES PAR LA COULEUR DU CHARGEUR.
M
ISE EN PLACE ET DECHARGEMENT DU CHARGEUR : FACILE, RAPIDE, PRECIS, SANS PERTES .
A
UCUN REGLAGE MACHINE POUR LES CHANGEMENTS DE TAILLE
REFERENCE TYPE
30303NCOI
30304NCOI
30305NCOI
31305BDCO 5 mmBD
30307NCOI
31307BDCO 7 mmBD
30310NCOI
31310BDCO 10 mmBD
30312NCOI
31312BDCO 12 mmBD
30315NCOI
31315BDCO 15 mmBD
Boites de 6 chargeurs de 275 agrafes
(1650 agrafes / boite)
A A
GRAFES EN GRAFES EN
AGRAFES ASSEMBLEUSES
®)
vous permettra d'obtenir un serrage
parfait de vos assemblages grâce à
sa déformation lorsqu'elle pénètre
dans le bois.
Suivant le type de bois utilisé, vous
choisirez la version :
Bois Normal (7 hauteurs disponibles)
ou Bois Dur (5 hauteurs disponibles).
F
ABRICATION EN ACIER DE QUALITE SUPERIEURE
T
RAITEMENT ANTI - CORROSION.
LA PENETRATION DANS LE BOIS.
JETABLES D' ENVIRON 275 AGRAFES
«BOIS DUR» PAR ETIQUETAGE .
P
RODUITS CONFORMES AUX NORMES INTERNATIONALES .
REFERENCE
3 mm 30403NCOI
VERT
30404NCOI
4 mm ORANGE
5 mm 304 05 NCOI
ROUGE 314 05 BDCO
304 07 NCOI
7 mm
314 07 BDCO
MAGENTA
304 10 NCOI
10 mm
CYAN 314 10 BDCO
304 12 NCOI
12 mm
BLEU 314 12 BDCO
304 15 NCOI
15 mm
314 15 BDCO1 15 mmBD
BLANC
Boites de 40 chargeurs de 275 agrafes
Cassese Communication 01 / 2002
W W
CS
Chargement de la CS 59
.
TYPE
3 mm
4 mm
5 mm
5 mm BD
7 mm
7 mm BD
10 mm
10 mmBD
12 mm
12 mmBD
15 mm
(11000 agrafes / boite)