Pattfield Ergo Tools E-LS 2445 Mode D'emploi D'origine page 13

Anleitung_E_LS_2445_SPK7:_
With the locking screw in horizontal position, plug the
vacuum tube into the motor housing.
Then use the supplied open-ended wrench to turn
the lever catch (3) 90° to the right (see Fig. 3a). The
vacuum tube is now locked in place.
Important: Please note that the two suction tubes
must always be joined together before they are
mounted on the motor housing, and that they
must never be taken apart when mounted!
Important: The garden blower vac is equipped
with a safety lock-off switch which only works
when the suction tube is mounted on the motor
housing.
5.2. Fitting the rake and vacuum nozzle (Fig. 3b)
The rake attachment (11) is connected to the
vacuum tube. The vacuum nozzle (12) is used for
vacuuming on level ground (e.g. tarmac or paving
stones).
When using the rake attachment or vacuum nozzle,
the guide rollers (9) do not come into operation.
5.3. Mounting the debris bag (Fig. 4)
Slip the debris bag (7) over the socket on the motor
housing. It engages correctly when it makes an
audible click. Then hang the hook on the suction
tube.
6.0 Prior to starting up
Start up the tool only after it is fully assembled.
Always inspect the tool power cord for damage
before starting up. The tool may only be used if the
cord is in flawless condition.
7.0 Starting up
7.1. Sizing the strap (Fig. 1)
●
Size the length of the carrying strap (4) so that
the vacuum tube just clears the ground. The
guide rollers (9) at the bottom end of the suction
tube will help you to maneuver the suction tube
on the ground.
7.2. Connecting the tool to the power supply and
switching on (Fig. 5, 6)
●
Insert the tool plug into the power cord coupling
(extension).
●
Secure the power cord (6) with the sleeve
provided on the tool as shown.
13.04.2011 11:28 Uhr Seite 13
●
To switch on, push the ON/OFF switch (5)
toward ON. To switch off, push the ON/OFF
switch toward 0FF.
7.3 Selecting the mode of operation
7.3.1 Vacuum (Abb. 7)
●
Turn the lever (8) all the way left to "Vacuum".
You can do this regardless of whether the tool is
running or not.
7.3.2 Blowing (Fig. 7)
●
Turn the lever (8) all the way right to "Blower".
You can do this regardless of whether the tool is
running or not.
●
Channel the air stream forward and walk slowly
to blow foliage or garden refuse into a pile or to
clear out hard-to-reach places.
Important!
Empty the debris bag before blowing. Otherwise, the
material that has been vacuumed up could drop out.
7.3.3 Emptying the debris bag and pre-screen
(Fig. 1)
Empty the debris bag (7) in good time. When the bag
is heavily loaded with material, vacuum power is
considerably reduced. Deposit organic refuse at a
compost site.
●
Switch off the tool and pull out the plug.
●
Open the zipper on the debris bag (7) and
shake out the material.
8.0 Maintenance and cleaning
IMPORTANT!
All maintenance, service and cleaning work must
be performed after the power cord has been
pulled out.
●
Do not use high-pressure cleaners or running
water to clean the tool.
●
Do not use any aggressive cleaning agents.
●
After shaking out the debris bag, turn it inside
out and thoroughly clean it in order to prevent
mould and unpleasant odors from forming.
●
You can use soap and water to clean out a
heavily soiled debris bag.
●
Rub a bar of dry soap across the zipper teeth if
the zipper becomes difficult to pull.
●
Always keep the tool and ventilation slats clean.
●
Use a damp rag to wipe dirt marks off of the
tool. Clean the vacuum/blower tube with a brush
upon evidence of dirt and grime.
GB
13