Cooper LumenSafe Instructions D'installation

Masquer les pouces Voir aussi pour LumenSafe:

Instructions d'installation (8 pages)

page de 10

/ 10
Signets

Les langues disponibles

Liens rapides

Télécharger ce manuel

IB512006EN

Installation Instructions – LumenSafe Ethernet Set Up Instructions

Instructions d'installation – Configuration du réseau Ethernet pour

système de caméras LumenSafe

Instrucciones de instalación – Instrucciones de configuración de

Ethernet LumenSafe

Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards- Installation and maintenance of this

product must be performed by a qualified electrician. This product must be installed in accordance

with the applicable installation code by a person familiar with the construction and operation of the

product and hazards involved.

Risk of Fire and Electric Shock- Make certain power is OFF before starting installation or attempting

any maintenance. Disconnect power at fuse or circuit breaker.

Risk of Fire- Refer to product label for specific minimum supply conductor requirements.

Risk of Burn- Disconnect power and allow fixture to cool before handling or servicing.

Risk of Personal Injury- Fixture may become damaged and/or unstable if not installed properly.

Failure to comply with these instructions may result in death, serious bodily injury and property damage.

DISCLAIMER OF LIABILITY: Cooper Lighting Solutions assumes no liability for damages or losses of any kind

that may arise from the improper, careless, or negligent installation, handling or use of this product.

NOTICE: Green ground wire provided in proper location. Do not relocate.

ATTENTION Receiving Department: Note actual fixture description of any shortage or noticeable damage on

delivery receipt. File claim for common carrier (LTL) directly with carrier. Claims for concealed damage must be

filed within 15 days of delivery. All damaged material, complete with original packing must be retained.

Safety: This fixture must be wired in accordance with the National Electrical Code and applicable local codes and

ordinances. Proper grounding is required to insure personal safety. Carefully observe grounding procedure under

installation section.

APPLICATIONS: This lighting fixture is designed for outdoor lighting services, and should not be used in area

of limited ventilation or inside high ambient temperature enclosures. It must be stored in a dry location prior to

installation. Do not expose lighting fixture to rain, dust or other environmental conditions prior to installation

and insertion of photo control or shorting cap (if so equipped). Best results will be obtained if installed and

maintained according to the following recommendations.

Regulatory Information: This equipment has been test and found to comply with the limits of a Class A digital

device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

WARNING

Brand Logo

reversed out of

black

LumenSafe

INS #

Sommaire des Matières pour Cooper LumenSafe

Page 1 Failure to comply with these instructions may result in death, serious bodily injury and property damage. DISCLAIMER OF LIABILITY: Cooper Lighting Solutions assumes no liability for damages or losses of any kind that may arise from the improper, careless, or negligent installation, handling or use of this product.
Page 2 Ensure Ethernet cable being brought into fixture is connected to an Internet Enabled Router. Router should assign automatic IP address to camera. Open Lumensafe Fixture and locate “Data in” Port on PoE injector inside fixture. (Figure 1.) Connect incoming Ethernet cable to “Data in” Port* of PoE injector inside fixture.
Page 3 Default Gateway: empty Open Lumensafe Fixture and locate “Data in” Port* on PoE injector inside fixture. (Figure 1.) Connect incoming Ethernet cable to “Data” in Port of PoE injector inside fixture. Pull up camera video stream by entering the camera’s IP address below into a web browser.
Page 4 Instructions d’installation – Configuration du réseau Ethernet pour système de caméras LumenSafe AVERTISSEMENT AVERTISSEMENT Risque d’incendie, de décharge électrique, de coupure ou d’autres accidents de personne – L’installation et l’entretien de ce produit doivent être effectués par un électricien qualifié. Ce produit doit être installé...
Page 5 Le routeur devrait assigner une adresse IP automatique pour la caméra. Ouvrez le luminaire LumenSafe et repérez le port « Data in » sur l’injecteur PoE à l’intérieur du luminaire. (Figure 1.) Branchez le câble d’entrée Ethernet au port « Data in »* de l’injecteur PoE à l’intérieur du luminaire.
Page 6 Passerelle par défaut : vide Ouvrez le luminaire LumenSafe et repérez le port « Data in » * sur l’injecteur PoE à l’intérieur du luminaire. (Figure 1.) Branchez le câble Ethernet d’entrée au port « Data in » de l’injecteur PoE à l’intérieur du luminaire.
Page 7: Renuncia De Responsabilidad
El incumplimiento de estas instrucciones puede provocar la muerte, lesiones corporales graves y daños materiales. RENUNCIA DE RESPONSABILIDAD: Cooper Lighting Solutions no asume ninguna responsabilidad por daños o pérdidas de ningún tipo que puedan derivarse de la instalación, manipulación o uso incorrecto, descuidado o negligente de este producto.
Page 8 Asegúrese de que el cable Ethernet que está en la luminaria esté conectado a un enrutador habilitado para Internet. El enrutador debe asignar una dirección IP automática a la cámara. Abra la luminaria LumenSafe y localice el puerto de “entrada de datos” en el inyector PoE dentro de la luminaria. (Figura 1.) Conecte el cable Ethernet entrante al puerto de "entrada de datos"* del inyector PoE dentro de la luminaria.
Page 9 Puerta de enlace predeterminada: vacío Abra la luminaria LumenSafe y localice el puerto de “entrada de datos”* en el inyector PoE dentro de la luminaria. (Figura 1.) Conecte el cable Ethernet entrante al puerto de "entrada de datos" del inyector PoE dentro de la luminaria.
Page 10 Veuillez consulter le site www.cooperlighting.com pour obtenir les conditions générales. Garantías y Limitación de Responsabilidad Visite www.cooperlighting.com para conocer nuestros términos y condiciones. Cooper Lighting Solutions Cooper Lighting Solutions is a registered 1121 Highway 74 South trademark. All trademarks are property Peachtree City, GA 30269 of their respective owners.