Product Specifications; Preparing For Use - F.F. Group BPS 25/40V PLUS Notice Originale

BPS 25/40V PLUS
flammable surfaces (e.g., paper, textiles, etc.) or
surroundings. The heating of the battery charger
during the charging process can pose a fire hazard.
Do not cover the ventilation slots of battery
f
charger. Otherwise, the battery charger can over-
heat and no longer operate properly.

PRODUCT SPECIFICATIONS

INTENDED USE
The machine is intended for domestic use, for pruning
trees and shrubs at elevated height, while the user is
situated on the ground. The machine is not intended
to cut inorganic material or to be used on a ladder or
steps. This tool is not intended for commercial or in-
dustrial use.
TECHNICAL DATA
Article Number
Model
Motor
Rated voltage
No load speed
Chain speed
Blade length
Max Reach
Run Time
No load running time
Oil reservoir capacity
Weight
Chain bar Model
Saw chain model
Battery model
(not included)
Charger model
(not included)
Sound emission values determined according to
EN 60745-1
Typically the A-weighted noise levels of the product are:
Sound pressure level
Guaranteed sound
power level
Uncertainty K
Vibration total values a
and uncertainty K determined according to EN
60745-1
Vibration level max:
a
h ,HD
42 407
BPS 25/40 PLUS
Brushless
V 36 (40max)
rpm 4.800 - 5.280
m/s 9,5
mm 254
m
min 25
min 70
ml 80
Kg 4,6
(100SDEA041) 254mm
(91P040X) 254mm
BLi 40V/5.0Ah
CH 40V/2A
dB(A) 76,3
dB(A) 95
dB 2,5
(triax vector sum)
h
m/s 1,542
2
K
IDENTIFICATION
1. Battery slot
2. Safety switch
3. Trigger
4. Pole
5. Telescoping release clasp
6. Angle adjustment button
7. Motor housing
8. Chain-tensioning ring
9. Cover Release Knob
10. Oil tank cover
11. Guide Bar
12. Saw Chain
13. Chain guard
14. Harness

PREPARING FOR USE

DANGER! To avoid serious personal injury, do
not operate the chainsaw without the chain
bar, saw chain, and side cover properly as-
sembled.
WARNING: Do not attempt to operate the
chainsaw if any part is damaged or missing.
FILLING THE BAR AND CHAIN OIL RESERVOIR
IMPORTANT! Bar and chain oil prevents pre-
mature wear. Never operate the chainsaw if
oil is not visible in the inspection window.
Check oil level frequently and fill as needed.
3
Bar and chain oil is required to properly lubricate the
f
chain bar and saw chain. The chainsaw is equipped
with an automatic oiler that deposits oil on the bar
and chain when running, keeping them properly
lubricated. It is specially designed to provide low
friction and faster cuts. NEVER use oil or other lu-
bricants that have not been specifically designed for
use on the bar and chain. This can lead to a clogged
oil system which may cause premature wear of the
bar and chain.
Place the chainsaw on a firm, flat surface so that the
f
oil cap (10) is on top.
Clean any debris from the cap area.
ƒ
Remove the cap (10).
ƒ
Carefully pour the bar and chain oil into the res-
ƒ
ervoir.
Replace the cap and make sure oil is visible in the
ƒ
reservoir.
TENSIONING THE SAW CHAIN
WARNING: If the chain is still loose when the
saw is at maximum tension, replace the chain.
IMPORTANT! Only tension the saw chain
when the chain is cool. A hot chain may con-
tract and damage the chain bar or chain as it
cools.
Wear gloves.
Remove the battery before tensioning.
ƒ
Loosen the side cover release knob (9) slightly,
ƒ
but do not remove the side cover.
Hold up the nose of the chain bar (E) and turn
ƒ
the chain tensioning ring (8) clockwise.
Tighten the chain tensioning ring until the low-
ƒ
English | 13
m/s 1,5
2
www.ffgroup-tools.com