Using The Machine - Kobra 400 HS Automatic Oiler Serie Mode D'emploi

SPECIFICATIONS
Congratulations on choosing a shredder equipped with an
inbuilt system that guarantees constant automatic lubrica-
tion of the cutting blades while the machine is in use. This
ensures continuous shredding capacity and a longer life for
your machine.
The Kobra 400 HS Automatic Oiler is suitable for shredding
single sheets and 9 ½" computer printouts.
The Kobra 400 HS-COMBI Automatic Oiler is suitable for sh-
redding single sheets and 9 ½" computer printouts as well
as CD-ROMS / DVDS and CREDIT CARDS.
The Kobra 400 HS-OM Automatic Oiler is only suitable for
shredding CD-ROMS / DVDS and CREDIT CARDS.
For specifications and cutting capacity, see table on page 22.
INSTALLATION
For machines with a removable plug, use an easily accessible
power socket near the machine.
Once the machine has been taken out of its packaging, open
the lid (A), take out the bag unit (B) from its tracks (C).
Remove the two safety screws used during transport (D).
Refit the plastic bag (E) in the bag unit (B) and reposition on
the tracks (C). Push the bag unit as far as it will go into the
container and close the lid (A).
WARNING: NOT inserting the bag unit as far as it will go will
mean that the lid will NOT close and all shredding functions
will be blocked.

USING THE MACHINE

KOBRA 400 HS AUTOMATIC OILER ( SEE FIG.1 )
After plugging the machine in to the mains, press button
(G) so that it is in the " I " position. The Stand-by light (1)
and the Energy Smart bar (3) will light up on the control
panel and the machine is ready to use. If the machine is
not then used, the Energy Smart bar (3) will go out while
keeping the machine on STAND-BY at practically zero power
consumption.
Documents can now be shredded at any time.
KOBRA 400 HS - OM AND KOBRA 400 HS - COMBI
AUTOMATIC OILER ( SEE FIG. 2 AND 3 )
After plugging the machine into the mains, press button (G)
so that it is in the " I " position. The Stand-by light (1) and the
Energy Smart bar (3) will light up on the control panel and
the machine will carry out an empty shredding cycle for a
few seconds, then stop, remaining ready for operation. If the
machine is not then used, the Energy Smart bar (3) will go
out while keeping the machine on STAND-BY at practically
zero power consumption.
Documents or optical media can now be shredded at any
time.
With the button (G) in the "0" position, all functions are
shut down.
SHREDDING SINGLE SHEETS
(a common function of the models Kobra 400 HS and Kobra
400 HS-COMBI Automatic Oiler ) see Fig.1 and Fig.3
Only for the Kobra 400 HS-COMBI Automatic Oiler, rotate
the metal flap (H) backwards, if it is down, to allow the sheets
of paper to pass through from the throat (4).
Inserting sheets of paper into the throat (4), switch on (if off)
the Optical Illuminated Indicator (3) and the machine will
automatically begin shredding. This is thanks to two photo
cells (5) located inside the throat, which read the passage of
the paper and automatically stop the cutting blades a few
seconds after shredding has been completed.
If a quantity of paper greater than the shredding capacity
of the machine is inserted, the machine will stop shredding
and reverse the direction of the rollers for a few seconds
before stopping.
Remove the unshredded paper from the throat (4) to free the
photo cells (5), then insert a smaller amount of paper in the
throat (4) and the machine will start up again automatically
to finish the shredding with a new shred cycle.
SHREDDING CD-ROMS / DVDS / CREDIT CARDS
KOBRA 400 HS - OM AUTOMATIC OILER, SEE FIG. 2
Raise the flap (Ha) , if down, to access the throat (4a).
When the optical media are inserted into the throat (4a), the
Optical Illuminated Indicator (3) comes on, if off, and the
machine automatically starts shredding. This is thanks to
two photo cells (5) located on the inside of the throat, which
read the passage of the optical media and automatically
stop the cutting blades a few seconds after shredding has
been completed.
IMPORTANT. Only insert one CD-ROM or DVD at a time.
KOBRA 400 HS - COMBI AUTOMATIC OILER, SEE FIG. 3
Raise the flap (Ha), if down, to access throat (4a).
When optical media are inserted into the throat (4a), it
switches on (if off) the Optical Illuminated Indicator (3) and
the machine automatically starts up.This is thanks to two
photo cells (5a) located on the inside of the throat which
read the passage of the optical media and automatically
stop the cutting blades a few seconds after shredding has
been completed.
IMPORTANT. Only insert one CD-ROM or DVD at a time.
This model comes with a special electronic blocking system
which prevents the use of the two throats (CDs and paper)
at the same time. If they are used together, shredding stops
and the machine goes into reverse for a few seconds. To
restart the blades, simply free the two throats and then only
insert either paper or a CD.
It is recommended to limit jams caused by insertion of
excessive quantities of paper and to operate the machine
below its maximum shredding capacity in order to prolong
the life of the mechanical parts and the machine itself.
ENERGY SMART Function: about 12 seconds after shredding
stops, the machine is put in energy saving mode; the
ENERGY SMART Optical Illuminated Indicator (3) switches
off, reducing power consumption to virtually zero.
This function yields an annual energy saving of approximately
10 kW, reducing carbon emissions (the cause of the ozone
hole) by 65 kg.
In order to automatically reactivate all the functions of the
machine, simply insert some sheets of paper or optical
media into the throat (4) or (4a) and engage the photo cells
(5) or (5a). The ENERGY SMART Optical Illuminated Indicator
(3) will then come on to show that the machine has been
reactivated.
9
Kobra Serie 400HS Auto Oiler