Specific Safety Rules - Welbach ALPHA 225 Manuel D'utilisation

4. Disconnect the Power Cord Plug from the power source before
making any adjustments, changing accessories, or storing the tool.
Such preventive safety measures reduce the risk of starting the tool accidentally.
5. Store idle tools out of reach of children and other untrained per-
sons. Tools are dangerous in the hands of untrained users.
6. Maintain tools with care. Keep cutting tools maintained and clean.
Properly maintained tools are less likely to bind and are easier to control. Do
not use a damaged tool. Tag damaged tools "Do not use" until repaired
7. Check for misalignment or binding of moving parts, breakage of
parts, and any other condition that may affect the tool's operati-
on. If damaged, have the tool serviced before using. Many accidents
are caused by poorly maintained tools.
8. Use only accessories that are recommended by the manufactu-
rer for your model. Accessories that may be suitable for one tool may become
hazardous when used on another tool.
Service
1. Tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel could result in a risk of injury.
2. When servicing a tool, use only identical replacement parts. Use of unauthorized
parts or failure to follow maintenance instructions may create a risk of electric
shock or injury.

SPECIFIC SAFETY RULES

1. Maintain labels and nameplates on the tool. These carry important
information. If unreadable or missing, contact our service team for a replacement.
2. Always wear the approved safety impact eye goggles and heavy
work gloves when suing the tool.
3. Maintain a safe working environment. Keep the work area well lit. Make
sure there is adequate surrounding workspace. Always keep the work area free
of obstructions, grease, oil, trash, and other debris. Do not use a power tool in
areas near flammable chemicals, dusts, and vapors. Do not use this product in a
damp or wet location.
EN
58
4. Avoid unintentional starting. Make sure you are prepared to begin work
before turning on the tool.
5. Never leave the tool unattended when it is plugged into an elec-
trical outlet. Turn off the tool, and unplug it from its electrical outlet before
leaving.
6. Always unplug the tool from its electrical outlet before perfor-
ming and inspection, maintenance, or cleaning procedures.
7. Prevent eye injury and burns. Wearing and using the approved personal
safety clothing and safety devices reduce the risk for injury.
a. Wear the approved safety impact eye goggles with a welding helmet
featuring at least a number 10 shade lens rating.
b. Leather leggings, fire resistant shoes or boots should be worn when using
this product. Do not wear pants with cuffs, shirts with open pockets, or any
clothing that can catch and hold molten metal or sparks.
c. Keep clothing free of grease, oil, solvents, or any flammable substances. Wear
dry, insulating gloves and protective clothing.
d. Wear an approved head covering to protect the head and neck. Use aprons,
cape, sleeves, shoulder covers, and bibs designed and approved for welding
and cutting procedures.
e. When welding/cutting overhead or in confined spaces, wear flame resistant
ear plugs or ear muffs to keep sparks out of ears.
8. Prevent accidental fires. Remove any combustible material from the work
area.
a. When possible, move the work to a location well away from combustible;
protect the combustibles with a cover made of fire resistant material.
b. Remove or make safe all combustible materials for a radius of 35 feet (10
meters) around the work area. Use a fire resistant material to cover or
block all open doorways, windows, cracks, and other openings.
c. Enclose the work area with portable fire resistant screens. Protect
combus tible walls, ceilings, floors, etc., from sparks and heat with fire
resistant covers.
d. If working on a metal wall, ceiling, etc., prevent ignition of combustibles on
the other side by mobbing the combustibles to a safe location. If relocation
of combustibles is not possible, designate someone to serve as a fire watch,
equipped with a fire extinguisher, during the welding process and for at least
one half hour after the welding is completed.
EN
59