Accessories - Milwaukee 0850-20 Manuel De L'utilisateur

CAUTION
largely dependent on the filter. A dirty filter will re-
duce the air flow and overall efficiency of the system.
Do not clean with water. Remove from dust canister
and tap clean or blow off with compressed air.
To install the dust canister:
1. Twist the filter onto the vacuum using the black
tabs to tighten securely.
2. Line up the dust canister with the unlock symbol
on the vacuum. Twist the rotate the dust canister
to the lock position. The dust canister latch should
click into place.
NOTE: Do not operate the vacuum without the dust
canister and filter in place.
Installing/Removing the Accessories
To install the nozzles or extension, push the acces-
sory onto the vacuum inlet.
OPERATION
WARNING
proper eye protection marked to comply with
ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
To reduce the risk of fire and injury, do not use
to pick up flammable or combustible materials.
Empty dust canister before use.
Fuel Gauge
To determine the amount of charge left in the battery,
turn the tool ON. The Fuel Gauge will light up for 2-3
seconds. When less than 10% of charge is left, 1 light
on the fuel gauge will flash 4 times.
To signal the end of charge, 1 light on the fuel gauge
will flash 8 times and the tool will not run. Charge
the battery pack.
If the battery becomes too hot, the fuel gauge lights
will flash in an alternating pattern and the tool will not
run. Allow the battery to cool down.
Starting, Stopping, and Controlling Air flow
1. To start the vacuum, pull the trigger.
2. To stop the vacuum, release the trigger.
To lock-on the trigger for continuous use:
1. Pull the trigger.
2. Press forward and hold the lock-on switch.
3. Release the trigger, then release the lock-on switch.
4. To stop the vacuum, pull and release the trigger.
MAINTENANCE
WARNING
the charger and remove the battery pack from
the charger or tool before performing any main-
tenance. Never disassemble the tool, battery
pack or charger. Contact a MILWAUKEE service
facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
Keep filter clean. Effi-
ciency of the vacuum is
To reduce the risk of
injury, always wear
Lock-on
To reduce the risk of
injury, always unplug
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
WARNING
age, never immerse your tool, battery pack or char-
ger in liquid or allow a liquid to flow inside them.
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use flammable or
combustible solvents around tools.
For repairs, return the tool, battery pack and charger
to the nearest authorized service center.

ACCESSORIES

WARNING
may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
SERVICE - UNITED STATES
1-800-SAWDUST
Monday-Friday, 7:00 AM - 6:30 PM CST
www.milwaukeetool.com
or visit
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: metproductsupport@milwaukeetool.com
B e c o m e a H e a v y D u t y C l u b M e m b e r a t
www.milwaukeetool.com to receive important
notifications regarding your tool purchases.
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
LIMITED WARRANTY USA & CANADA
Every MILWAUKEE power tool* (see exceptions below) is warranted to the
original purchaser only to be free from defects in material and workman-
ship. Subject to certain exceptions, MILWAUKEE will repair or replace any
part on an electric power tool which, after examination, is determined by
MILWAUKEE to be defective in material or workmanship for a period of
five (5) years** after the date of purchase unless otherwise noted. Return
of the power tool to a MILWAUKEE factory Service Center location or
MILWAUKEE Authorized Service Station, freight prepaid and insured,
is required. A copy of the proof of purchase should be included with the
return product. This warranty does not apply to damage that MILWAUKEE
determines to be from repairs made or attempted by anyone other than
MILWAUKEE authorized personnel, misuse, alterations, abuse, normal
wear and tear, lack of maintenance, or accidents.
Normal Wear: Many power tools need periodic parts replacement and
service to achieve best performance. This warranty does not cover repair
when normal use has exhausted the life of a part including, but not limited
to, chucks, brushes, cords, saw shoes, blade clamps, o-rings, seals, bum-
pers, driver blades, pistons, strikers, lifters, and bumper cover washers.
*This warranty does not cover Air Nailers & Staplers; Airless Paint Sprayer;
Cordless Battery Packs; Gasoline Driven Portable Power Generators; Hand
Tools; Hoist – Electric, Lever & Hand Chain; M12™ Heated Gear; Recon-
4
To reduce the risk of
personal injury and dam-
Cleaning
Repairs
Use only recommended
accessories. Others
(1.800.729.3878)