Midi Channel Setting - Eagletone DMX DISCONTROL 192 Manuel De L'utilisateur

User's manual
TAP SYNC/Display button three times. The chase will then
run based on the time interval of your taps.
Note:
- N ever adjust Fade time slower than the Speed setting
otherwise your scenes will not be completed before a new
step is sent!
- I f you wish to include all the chases, press the Auto/Del
button before selecting the Chase.
Music Run Chases
• Press one of the six Chase buttons to select your desired
chase.
• Press and release the Music/Bank-Copy button.
• The corresponding LED will flash in the LCD.
• Your chase will now run to the sound.
Note:
- When you exit a chase by pressing the Chase button, the
controller will automatically run the scenes in the last
bank that was accessed. To stop the movement of the
lights, use the Blackout button or press the Music button
if the unit is in music mode or the Auto button.

Midi Channel Setting

MIDI Running
• Press and hold the MIDI/Add button down. The third and
fourth digits of the LED display will blink, indicating MIDI
mode is activated.
• Use the Up and Down buttons to select the MIDI channel (1
to 16) you would like to run.
• Press and hold the MIDI/Add button down once more to
deactivate the MIDI mode.
MIDI Channel settings
Note on: Receives Note On signals to execute corresponding
functions.
The DMX Discontrol 192 receives only MIDI notes and you
might have to transpose your keyboard to find the proper
notes.
TROUBLESHOOTING
Colors do not respond when faders are moved.
Make sure the address is correct. If the XLR cable is more
than 30 meters long, check if it is terminated properly.
Mirrors do not respond when faders are moved.
Make sure the address is correct.
Make sure the speed is adjusted, if available, for faster
movement. Not all fixtures have a speed adjustment. If
the XLR cable is more than 30 meters long, check if it is
terminated properly.
Scenes do not run after I recorded them.
Make sure to press the MIDI/Add button before pressing the
Scene button.
LEDs should blink after each Scene button is pressed. Make
sure you are in the correct Bank that contains the recorded
scenes.
Scenes do not run the way I recorded them
Make sure all fixtures were recorded. Make sure you are
in the correct Bank that contains the recorded scenes. If
the XLR cable is more than 30 meters long, check if it is
terminated properly.
Chases do not run after I recorded them.
Make sure to press the MIDI/Add button after pressing the
Scene button. The LED should blink after pressing the MIDI/
Add button.
Make sure you are in the correct Chase that contains the
steps you recorded. If you are in Auto Mode, did you adjust the
4
speed after selecting Auto? Is the Fade time too long for the
speed you selected? If the XLR cable is more than 30 meters
long, check if it is terminated properly.
SPECIFICATIONS
Power input: DC9~12V 300mA min.
DMX Output: 3-pin female XLR.
Size: 19" × 5.25" × 3" (inch).
EC Declaration of Conformity
We declare that our product complies with the following
specification and bears CE mark in accordance with the provision of
the Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
EN55014-1:1993, EN61000-3-2: 1995, EN61000-3-3: 1995
EN55014-2: 1997 CATEGORY II
EN61000-4-2: 1995, EN61000-4-3: 1995, EN61000-4-4: 1995
EN61000-4-5: 1995, EN61000-4-6: 1995, EN61000-4-11: 1994
Harmonized Standard
EN60598-1: 1993
Safety of household and similar electrical appliances
Part 1: General requirements
Following the provisions of the Low Voltage Directive 73/23 EEC and
93/68/EEC
eagletone.com
EAGLETONE DMX DISCONTROL 192