Chase Programming - Eagletone DMX DISCONTROL 192 Manuel De L'utilisateur

EAGLETONE DMX DISCONTROL 192
flash shortly to indicate the copy has been finished.
Delete a Bank
Press and hold the Program button down for three seconds to
activate the programming mode.
Select the bank to delete. Press the Auto/Del and Music/
Bank-Copy buttons simultaneously to delete the Bank. The
LCD will flash to indicate the deletion is completed.

Chase Programming

You have to program scenes before you can program chases.
• Press and hold the Program button down for 3 seconds to
enter the programming mode.
• Choose any chase (1~6) to be programmed.
• Select the desired Scene from any bank. Scenes are run in
the order they are programmed into the chase.
• Press the MIDI/Add button, all the LEDs will flash 3 times.
• Repeat steps 3 and 4 as many times as you want. You can
record up to 240 scenes into one chase.
• Press and hold the Program button down for 3 seconds to
exit the programming mode.
Copy a Bank to a Chase
• Press and hold the Program button down for three seconds
to enter the programming mode.
• Select the bank of scenes you wish to copy.
• Select the chase to which you want to copy the bank of
scenes.
• Press the Music/Bank-Copy and MIDI/Add buttons
simultaneously. The scenes of the bank are copied to the
Chase.
• Press and hold the Program button down for three seconds
to exit the programming mode.
Editing chases
Adding a Step to a Chase
• Press and hold the Program button down for three seconds
to enter the programming mode.
• Select the chase 1 ~ 6 to which you wish to add a step.
• Press TAP SYNC/Display and the LCD shows the scene and
bank. This is the bank containing the scene you wish to add.
• Press TAP SYNC/Display again and the LCD shows the
Chase that you have selected.
• Use the Up and Down buttons to scroll through the chase to
reach the step after which you wish to add a step.
• Press MIDI/Add, the LCD will read one step number higher.
• Press the Scene button you wish to add.
• Press MIDI/Add again to add new step.
• Press and hold the Program button down for three seconds
to exit the programming mode.
Deleting a Step in a Chase
• Press and hold the Program button down for three seconds
to enter the programming mode.
• Select the Chase 1 to 6 from which you wish to delete a step.
• Press TAP SYNC /Display and the LCD shows the Chase
that you have selected.
• Use the Up/Down buttons to scroll through the chase to
reach the step you wish to delete.
• Press Auto/Del and the scene will be deleted.
• Press and hold the Program button down for three seconds
to exit the programming mode.
Delete chase (all scenes are still available)
• Press and hold the Program button down for three
seconds.
• Press the Chase button corresponding to the chase you
want to delete.
• Press and hold the Auto/Del button down and then press
and hold the Chase button down of the chase to be deleted.
The LEDs will flash three times.
• Release both buttons and the chase will be deleted.
Delete All Chases (all scenes are still available)
• Press and hold the Bank Down and Auto/Del buttons down
while turning the power off.
• Reconnect the power, all chases should be deleted.
Running Scenes
Manual Run Scenes
When the power is first turned on, the unit is in Manual scene
mode.
• If you are in Program mode, press and hold the Program
button down for three seconds and the Program LED will
go out. The controller is now in Manual mode.
• Make sure the Auto & Music button LEDs are off.
• Select the Bank using the Up and Down Bank buttons that
stores the scenes you wish to run.
• Press the Scene button to run the scenes you selected.
Auto Run Scenes
This function will run a bank of programmed scenes in a
sequential loop.
• Press Auto/Del once to activate the Auto Run mode.
• Use the Up and Down Bank buttons to select a bank of
scenes to run.
• Now you can use the speed and fade sliders to adjust the
scenes to your liking. The fade setting should never be
slower than the speed setting or the scenes will not be
completed.
• You can change banks on the fly by pressing the Up and
Down Bank buttons.
Music Run scenes
• Press the Music/Band-Copy button and the corresponding
indicator will light up on the LCD.
• Select the bank that stores the scenes you wish to chase by
using the Up or Down buttons or MIDI signals.
• Press Music/Bank-Copy once more to exit the music mode.
MIDI Run Scenes
• Select the bank from which to run the scenes using MIDI
whenever the unit is in Manual, Auto or Music Run mode.
Running Chases
Manual Run Chases
This function will enable you to manually step through a
selected chase.
• Press and hold the Program button down for three seconds
to enter the programming mode.
• Start a chase by selecting one of the six Chase buttons.
• Press the TAP SYNC button. Each time you press the
button, you will step through the chase.
• Use the Bank selection buttons to scroll through the
chases.
• Press and hold the Program button for down three seconds
to exit the programming mode.
Auto Run Chases
• Press any or all six Chase buttons to select the desired
chase.
• Press and release the Auto /Del button. The corresponding
LED will flash.
• Adjust the Speed and Fade Time to your desired settings.
The Chase will run according to your settings.
• You can override the speed and fade time by tapping the
eagletone.com
User's manual
3