General Safety Instructions; Safety Instructions For Assembly; Safety Instructions For Operation - Husqvarna CG 200 Manuel D'utilisation

Masquer les pouces Voir aussi pour CG 200:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

General safety instructions

WARNING: Please read the operator's
manual carefully and make sure you
understand the instructions before using the
product.
The product is designed to provide safe and reliable
service in operating conditions corresponding with the
instructions, but it can present dangers for the user and
risks of damage, consequently regular on site inspection
is necessary to ensure:
Perfect technical condition (use for the purpose for
which it is intended and taking into account any
risks, and correction of any malfunction detrimental
to safety).
That the warnings and instructions marked on the
product are followed (adequate personal protection,
correct use, general safety instructions, etc).
The product is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge.
Children shall be supervised not to play with the
appliance.
That the product is for commercial use.
That overexposure to vibration can lead to
circulatory damage or nerve damage in people who
have impaired circulation. Contact your doctor if you
experience symptoms of overexposure to vibration.
Such symptoms include numbness, loss of feeling,
tingling, pricking, pain, loss of strength, changes in
skin colour or condition. These symptoms normally
appear in the fingers, hands or wrists. These
symptoms may be increased in cold temperatures.
Cutting, especially when DRY cutting, generates
dust that comes from the material being cut, which
frequently contains silica. Silica is a basic
component of sand, quartz, brick clay, granite and
numerous other minerals and rocks. Exposure to
excessive amount of such dust can cause:
Respiratory disease (affecting your ability to
breath), including chronic bronchitis, silicosis and
pulmonary fibrosis from exposure to silica. These
diseases may be fatal.
Skin irritation and rash.
Cancer according to NTP* and IARC* */ National
Toxicology Program, International Agency for
Research on Cancer
Take precautionary steps:
Avoid inhalation of and skin contact with dust,
mist and fumes.
Wear and ensure that all bystanders wear
appropriate respiratory protection such as dust
masks designed to filter out microscopic
particles. (See OSHA 29 CFR Part 1910.1200)
Wet cut when feasible, to minimize dust.
6
WARNING: Do not allow the supply cord to
come in contact with rotating brushes.
Note: Operator´s manual should always be available at
the place of work. It should be read and used by any
person installing or using the product. The obligatory
technical regulations in force in the country where the
product is used must also be adhered to for maximum
safety.

Safety instructions for assembly

The original drums from manufacturers' should be used.
Do not use any other drum whose shape, size and
mounting do not fit the product.
Check that the parts are properly fixed (no abnormal
vibration) and that it is correctly assembled.
No modification, transformation or addition that is
detrimental to safety and that it is carried out without
prior authorization from the manufacturer should be
done.

Safety instructions for operation

WARNING: This section describes basic
safety directions for using the product. This
information is never a substitute for
professional skills and experience. If you get
into a situation where you feel unsafe, stop
and seek expert advice. Contact your
dealer, service agent or an experienced
user. Do not attempt any task that you feel
unsure of!
WARNING: The toolshaft rotates when the
engine is started.
WARNING: Be aware of hot muffler. Use
gloves/safety gear.
Those who operate this product should be competent
staff (qualifications, age, training) who have read and
understood the manual in detail before starting work.
Any electrical, mechanical or other problem should be
investigated by a qualified maintenance engineer
(electrician, maintenance manager, approved dealer,
etc .).
When the product is recived check its condition.
Always keep the product clean.
Always keep alert when working.
130 - 003 - 18.08.2017

Publicité

Table des Matières
loading

Table des Matières