Start Up; Channeling System; How To Place The Optional Ductable Kit (Only On Boreal-9 And Boreal-12 Models) - BOREAL AIR Série Instructions D'installation, D'utilisation Et D'entretien

It must be placed in so that it cannot be obstructed. It must be connected to the environment where the equipment is installed and it must be protected by
a grate. The minimum area of the outlet should not be less than 100 cm2.
When the air flow comes through openings that are connected to the exterior of adjacent environments, it is important to avoid air intakes in connection
with garages, kitchens, toilets, etc.
EN
The stove is provided with a necessary air intake for the combustion on the back side (40 or 50 mm diameter). It is important this intake is not blocked
and to respect the recommended distances to the wall or near items.
It is recommended the primary air intake connection of the stove with the outside although it is not obligatory. The connection tube material can be
made in any material (PVC, aluminium, polyethylene, etc.), not necessarily metallic. Consider that inside this duct is going to pass air at the outside
temperature.
The Boreal-9 model is certified as an open combustion boiler through the standard EN613 (50Pa), it is therefore
a model that is certified to operate with the PGI system by Poujoulat. Thanks to the supply line´s airtight setting
and the smoke pipes the stove can be used in hermetic locations (passivhaus – BBC)
Thanks to an airtight combustion chamber, this product can operate by getting the oxygen from outside, through
this means, the use (or consumption) drops dramatically and the thermal comfort increases in the most modern houses
(Class A).

6. START UP

The ignition of this kind of equipments is automatic, so, please do not put on the burner any kind of material to ignition.
Before the ignition, follow the next verifications:
It is forbidden to use liquid substances such as alcohol, gasoline, petroleum or similar products. The use of this substance leads the loss of
warranty.
- The electrical cable must be connected to the electrical network (230 Vac) with a socket equipped with earthing system.
- The bipolar switch, placed on the rear side of the stove, must be in position I.
- The pellet tank must be supplied.
- The combustion chamber must be clean.
- The burner must be clean and properly placed.
- The combustion chamber door must be closed correctly.
During the first ignition could happen that the stove has finished the ignition cycle and there is no flame. In this case the stove automatically starts an
alarm state. This happens because the fuel feeder is empty and needs a moment to fill in. To solve this problem start again the stove (taking into account
the previous considerations ) until the flame appears.
The stove, at the beginning, must be subject to different start-up cycles so that all materials and the paint can complete different elastic expansions.
At the beginning, it is possible that you note smoke or smell which are typically produced when metals are subject to high temperatures or when the
paint is still fresh. This paint is boiled at 80º C for a few minutes when construction, but it must exceed for a time the temperature of 200 ºC before the
adhesion to the metallic surfaces.
Therefore, it is important to adopt these measures during the ignition phase:
1. Assure that there is a good air refill in the place where the equipment is installed.
2. During the firsts ignitions, keep a low power work and the oven lit during at least 6-10 hours continuously.
3. Repeat this operation at least 4-5 times or more, depending on the needs.
4. During the first ignitions, you should not place any object on the equipment and, in particular, on lacquered surfaces. Lacquered surfaces should
not be touched while the equipment is heated.

7. CHANNELING SYSTEM

You will find detailed below the operation of the air distribution system to other adjacent or upper rooms for the
models Boreal-9 and Boreal-12 with the purchase of the optional channeling kit.
Menú 01
VENT-2
7.1

HOW TO PLACE THE OPTIONAL DUCTABLE KIT (ONLY ON BOREAL-9 AND BOREAL-12 MODELS)

If you have purchased an optional ductable kit which is made up of a fan with a connector and a connection cable that goes to the electronic plate, you
should remind the next steps to follow for its right installation.
- In the first place, you should take apart the side chambers in order to access to the inside of the stove.
- Right after you should set the connector and the turbine in the right place and proceed to its attachment by placing and tightening all of the three
screws that are supplied.
- Finally you should plug in the turbine cable with the electronic plate, in the CN6 "V2/PO" connector. Do not forget to switch off the supply before
carrying out this connection.
24
This models includes on the rear side one exit with a 80 mm diameter
corresponding with the forced air output channelling system to heat other
adjacent or upper room.The regulation of the channeling system is done through
the electronics of the stove, being able to select the channeling operation,
selecting the desired power level for the channeling fan independently of the
main fan. To do this you have to gain access to menu 1 and choose the fan
1
activation and the working power.
Note: Please note that if you have a Boreal-6 model, this model can't be ductable, so this menu is visible but it
lacks functionality. We remind you that in these models you can only modify the speed of the fan 2, because this
model has only one.
Menú 01
VENT-2 1