DAB PUMPS e.sybox Manuels

Manuels et Guides d'utilisation pour DAB PUMPS e.sybox. Nous avons 1 DAB PUMPS e.sybox manuel disponible en téléchargement PDF gratuit: Instructions Pour L'installation Et L'entretien

DAB PUMPS e.sybox Instructions Pour L'installation Et L'entretien

DAB PUMPS e.sybox Instructions Pour L'installation Et L'entretien (113 pages)

Marque: DAB PUMPS | Catégorie: Pompes | Taille: 7.11 MB

Table des Matières

English

3
- Table des Matières
  3
- Key
  6
- Warnings
  6
- Responsibility
  7
- General
  7
- Description of the Integrated Inverter
  8
- Integrated Expansion Vessel
  8
- Integrated Electropump
  10
- Technical Characteristics
  10
- Installation
  11
- Vertical Configuration
  12
- Hydraulic Connections
  12
- Loading Operation Installation above Head and below Head
  13
- Horizontal Configuration
  13
- Hydraulic Connections
  14
- Orientation of the Interface Panel
  14
- Electrical Connections
  15
- Commissioning
  15
- Loading Operation Installation above Head and below Head
  15
- Configuration of the Integrated Inverter
  16
- Priming
  16
- Protection Systems
  17
- Anti-Freeze (Protection against Freezing of Water in the System)
  18
- BP1" Blockage Due to Fault of the Internal Pressure Sensor
  18
- SC" Blockage Due to Short Circuit between the Motor Phases
  18
- Anti-Cycling (Protection against Continuous Cycles Without Utility Request)
  18
- BL" Aanti Dry-Run (Protection against Dry Running)
  18
- Description of Blockages
  18
- Manual Reset of Error Conditions
  19
- Self-Reset of Error Conditions
  19
- Inverter Electronic Control and User Interface
  19
- Operation with Control Unit
  19
- Functions Made Available by Control Units
  20
- Electrical Connections of Utility Inputs and Outputs
  20
- Safety Mode Operation
  20
- Control Unit Function Setup
  21
- Association and Disassociation of E.sybox and Control Unit
  21
- The Keypad and the Display
  22
- Direct Access with a Combination of Keys
  23
- Access by Name with a Drop-Down Menu
  26
- Structure of the Menu
  27
- Blocking Parameter Setting by Password
  28
- Enabling and Disabling the Motor
  28
- Meaning of the Individual Parameters
  28
- User Menu
  28
- Status
  28
- RS: Rotation Speed Display
  28
- VP: Pressure Display
  28
- VF: Flow Display
  28
- Multi-Pump System
  29
- VE: Version Display
  29
- Output Flow Meter
  29
- PO: Absorbed Power Display
  29
- PI: Power Histogram
  29
- Operating Hours and Number of Starts
  29
- C1: Phase Current Display
  29
- TE: Dissipator Temperature Display
  30
- Setting the Auxiliary Pressures
  30
- SP: Setting the Setpoint Pressure
  30
- Setpoint Menu
  30
- FF: Fault Log Display
  30
- LA: Language
  30
- TK: Backlight Switch-On Time
  30
- BK: Display Brightness
  30
- CT: Display Contrast
  30
- Monitor Menu
  30
- P1: Setting the Auxiliary Setpoint
  31
- P2: Setting the Auxiliary Setpoint
  31
- P3: Setting the Auxiliary Setpoint
  31
- P4: Setting the Auxiliary Setpoint
  31
- Manual Menu
  31
- RS: Rotation Speed Display
  32
- RP: Setting the Pressure Fall to Restart
  32
- Installer Menu
  32
- TE: Dissipator Temperature Display
  32
- Status
  32
- C1: Phase Current Display
  32
- VF: Flow Display
  32
- VP: Pressure Display
  32
- RI: Speed Setting
  32
- PO: Absorbed Power Display
  32
- AD: Address Configuration
  33
- MS: Measuring System
  33
- AS: Association of Devices
  33
- PR: Remote Pressure Sensor
  34
- Technical Assistance Menu
  34
- TB: Water Lack Blockage Time
  34
- Setting the Number of Devices and of Reserves
  35
- IC: Configuration of the Reserve
  35
- NC: Simultaneous Devices
  35
- NA: Active Devices
  35
- RM: Maximum Speed
  35
- GP: Proportional Gain Coefficient
  35
- T2: Delay in Switching off
  35
- GI: Integral Gain Coefficient
  35
- Examples of Configuration for Multipump Systems
  36
- ET: Max. Switching Time
  36
- AF: Enabling the Anti-Freeze Function
  37
- Setup of the Auxiliary Digitali Inputs IN1, IN2, IN3, IN4
  37
- AE: Enabling the Anti-Block Function
  37
- AY: Anti Cycling
  37
- Disabling the Functions Associated with the Input
  38
- Setting External Float Function
  38
- Setting Auxiliary Setpoint Input Function
  38
- Setting System Enabling and Fault Reset
  39
- Setting Low Pressure Detection (KIWA)
  40
- Setup of the Outputs OUT1, OUT2
  40
- PW: Change Password
  41
- RF: Fault and Warning Reset
  41
- FW: Firmware Update
  41
- O2: Setting Output 2 Function
  41
- O1: Setting Output 1 Function
  41
- Password for Multipump Systems
  42
- Reset and Factory Settings
  42
- Factory Settings
  42
- Restoring the Factory Settings
  42
- Particular Installations
  44
- Inhibiting Self-Priming
  44
- Wall Installation
  45
- Installation with Quick Connection
  45
- Multiple Sets
  45
- Introduction to Multipump Systems
  45
- Making a Multipump System
  45
- Wireless Communication
  46
- Connection and Setting of the Inputs
  46
- Parameters Linked to Multipump Operation
  46
- First Start of the Multipump System
  47
- Multipump Adjustment
  47
- Assigning the Starting Order
  48
- Max. Switching Time
  48
- Reaching the Maximum Inactivity Time
  48
- Reserves and Number of Devices that Participate in Pumping
  48
- Wireless Control
  49
- Maintenance
  49
- Accessory Tool
  49
- Emptying the System
  51
- Non-Return Valve
  51
- Motor Shaft
  52
- Expansion Vessel
  52
- Updating the E.sybox Firmware
  52
- General
  52
- Automatic Updating
  53
- Manual Updating
  53
- Updating between One E.sybox and Another
  53
- Updating the Firmware
  53
- Semiautomatic Updating
  54
- Updating the E.sybox by E.sylink
  54
- Troubleshooting
  54
- Disposal
  56
- Guarantee
  56
Français

57

Publicité

Publicité

Produits Connexes

DAB PUMPS Catégories

Plus Manuels DAB PUMPS