Télécharger Imprimer la page

Fortin EVO ONE THAR-FOR4 Schéma D'installation page 7

Installation harnais, addenda - schéma de branchement suggéré pour ford escape 40-bits 2011-2012, escape hybrid 40-bits 2008-2012
Masquer les pouces Voir aussi pour EVO ONE THAR-FOR4:

Publicité

This guide may change without notice. See www.fortin.ca for latest version.
Ce guide peut faire l'objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
KEY BYPASS PROGRAMMING PROCEDURE 2/2 | PROCÉDURE DE PROGRAMMATION CONTOURNEMENT DE CLÉ 2/2
7
TURN
ON/RUN
8
TURN
OF
F
9
8
TURN
OF
F
10
FLASH LINK UPDATER*
OR
OU
VEHICLE'S OBDII
CONNECTOR
CONNECTEUR OBDII
DU VÉHICULE
11
IGNITION OFF
ON
IGNITION OFF
ON
ON
IGNITION OFF
ON
ON
FLASH LINK MANAGER*
SOFTWARE | PROGRAMME
FLASH LINK MOBILE*
The module is now programmed.
Le module est programmé.
 The RED LED will turn OFF.
FLASH
 WAIT, the BLUE LED to flash
rapidly.
Turn the key to the
IGNITION ON
Ignition ON/RUN position.
ON
OFF
The YELLOW LED will turn
OFF
on and off.
The RED LED will turn OFF.
FLASH
 WAIT, the BLUE LED to flash
rapidly.
Turn the key to the
FLASH RAPIDLY
OFF position.
 The RED and YELLOW LEDs
will alternate.
Disconnect all connectors and after the 4-PIN
Data-link harness (Black connector).
Débranchez tous les connecteurs et ensuite le
Turn the key to the
FLASH RAPIDLY
harnais Data-Link à 4-Broches (connecteur Noir).
OFF position.
 The RED and YELLOW LEDs
Microsoft Windows
will alternate.
Computer with
Internet connection*
Ordinateur Microsoft
Windows avec
connection Internet*
Use the tool:
FLASH LINK UPDATER or
FLASH LINK MOBILE
to visit the DCryptor menu.
Smartphone*
*Parts required (not included)
Téléphone
Intelligent*
AFTER DCRYPTOR PROGRAMMING COMPLETED
Go back to the vehicle and reconnect the the 4-PIN
Data-link harness (Black connector) and after all the
remaining connector.
APRÈS LA PROCÉDURE DE PROGRAMMATION
DCRYPTOR COMPLETÉE : retournez au véhicule et
rebranchez le harnais Data-Link à 4-Broches
(connecteur Noir) et après tous les connecteurs.
REMOTE STARTER / ALARM VERIFICATION
PROCEDURE | PROCÉDURE DE VÉRIFICATION
DU DÉMARREUR À DISTANCE / ALARME
Test the remote starter. Remote start the vehicle.
Testez le démarreur à distance. Démarrez le véhicule
à distance.
 La DEL ROUGE s'éteint.
 ATTENDRE que la DEL
BLEUE clignote rapidement.
Tournez la clé à Ignition.
La DEL JAUNE s'allume et
s'éteint.
 La
DEL ROUGE s'éteint.
 ATTENDRE que la DEL
BLEUE clignote rapidement.
Tournez la clé à la
position Arrêt (OFF).
 La DEL ROUGE et JAUNE
alternent.
Tournez la clé à la
position Arrêt (OFF).
 La DEL ROUGE et JAUNE
alternent.
Utilisez l'outil:
FLASH LINK UPDATER ou
FLASH LINK MOBILE
pour visitez le menu DCryptor.
*Pièces requises (non incluses)
7 / 9
Page

Publicité

loading