Cequent Performance Products 36520 Instructions D'installation

Frame rail
Hitch Shown In Proper Position
Equipment Required: Tape, Utility Knife, Tape Measure &
Marking Pencil, Lubricant or Soapy water
Fastener Kit: 36520F
Wrenches: 10mm, 17mm, 11/16,
Small Phillips head Screwdriver,
Apperance panel
16.25
Tie down
hook cut-out
Area to be Trimmed
1 1 1 1 Qty. (4) Hex Bolt M10X1.25X30 CL8.8
2 2 2 2
Qty. (4) Conical Washers 7/16"
3 3 3 3 Qty. (1) 3/8-16 U-Bolt
4 4 4 4 Qty. (2) Flat Washer 3/8"
1. Remove the appearance panel on driver's side, remove 5-plastic rivets, 3-hex nuts, 2 Phillips head screws located in wheel well behind
the driver's side rear tire. This panel needs to be trimmed and reinstalled on vehicle.
2. Run the (item 1) into existing weld nuts to clear the threads.
3. Reinstall appearance panel if trimmed.
4. Lower exhaust by removing rubber isolators from muffler hangers. Remove the outside isolator first then the inside isolator. Spraying
a lubricant or soapy water on the metal hanger rod and the rubber isolator helps removal.
5. Tape (item 7) flat washer to rearward weld nut location on both frame rails.
6. Raise hitch into position.
7. Install M10 fasteners as shown.
8. Install the 3/8 U-Bolt through the vehicle tie down hook and through the tie down hook attachment of the receiver. Install flat washer,
lock washers and 3/8 hex nuts as shown above.
9. Tighten all fasteners to the required torque specification.
10. Raise exhaust back into position and re-install rubber isolators.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
© 2012, 2015 Cequent Performance Products, Inc. – Printed in México
Installation Instructions
Honda CR-V
(Sold separately)
Fascia
Drawbar Kit:
36051
Drawbar must be used in the
Rise position only.
8.50
3.00
4.25
Tighten all 3/8-16 GR5 fasteners with torque wrench to 30 Lb.-Ft. (41 N*M)
Tighten all M10 CL8.8 fasteners with torque wrench to 38 Lb.-Ft. (52 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
3500 LB (1589 Kg) Max Gross Trailer Weight
300 LB (136 Kg) Max Tongue Weight
Existing weld nuts
typical
Inside isolator
Tie
down
hook
3
Exhaust shown lower
Note:
Fasteners typical both sides
5 5 5 5 Qty. (2) Lock Washer 3/8"
6 6 6 6
Qty. (2) 3/8 Hex Nut
7 7 7 7 Qty. (2) Flat washer ½"
Sheet 1 of 3 36520N
Part Numbers:
36520
90089
06144
36350
Wiring Access Location: SUV3
Tape flat
washer to
frame rail
4
5
6
10-9-15
Form: F205 Rev A 5-6-05
U-Haul
7
2
1
2
1
Rev. D