Accessories - Craftsman CMPNC18 Guide D'utilisation

2. Keep tool as warm as possible prior to use.
3. Make certain all fasteners have been removed
from magazine.
4. Lower air pressure to 80 p.s.i.g. (5.7 kg/cm
5. Reconnect air and and load nails into magazine.
6. Turn pressure up to operating level (not to exceed
120 p.s.i.g. [8 kg/cm 2 ]) and use tool as normal.
7. Always drain the compressor tanks at least once a day.
Hot Weather Operation
Tool should operate normally. However, keep tool out
of direct sunlight as excessive heat can deteriorate
bumpers, o-rings and other rubber parts resulting in
increased maintenance.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove air supply before
making any adjustments or removing/installing
attachments or accessories. An accidental
actuation can cause injury.
Action Why
Drain compressor Prevents accumulation
tanks and hoses of moisture in
daily. compressor and nailer.
Clean magazine, Permits smooth
magazine release operation of magazine,
and contact trip reduces wear and
mechanism. prevents jams.
Before each use, Prevents jams, leaks
check to insure all and premature failure
screws, nuts and of tool parts.
fasteners are tight
and undamaged.
Before each use, Prevents jams, leaks
check to insure all and premature failure
screws, nuts and of tool parts.
fasteners are tight
and undamaged.

Accessories


WARNING: Since accessories, other than those
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be
used with this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1-888-331-4569.
) or less.
2
Versatrack™ (Fig. G)





How
Open petcocks or

other drain valves
on compressor
tanks. Allow any
accumulated water to
iMPORTAnT: Versatrack™ accessories mount compatible
drain from hoses.
tools securely to the Versatrack™ Trackwall system.
Blow clean with
1. Turn tool off, remove air supply and remove accessories.

compressor air. The
use of oils, lubricants
periodically or solvents
is not recommended
2. Attach the hang hook
as they tend to attract
a. Use a wrench to remove the fitting
debris.
b. Place the Versatrack™ hang hook on the fitting.
Tighten loose screws or
c. Use a wrench to re-install the fitting at the base of
other fasteners using
the appropriate hex
nOTE: Versatrack™ accessories for use with your tool are
wrench or screwdriver.
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
Tighten loose screws or
accessory, please contact CRAFTSMAN, call 1-888-331-4569.
other fasteners using
the appropriate hex
wrench or screwdriver.
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove air supply before
making any adjustments or removing/installing
attachments or accessories. An accidental
actuation can cause injury.
WARNING: To reduce the risk of serious personal
injury, do not use a damaged Versatrack™ hang hook
or Versatrack™ Trackwall. A damaged Versatrack™
hang hook or Versatrack™ Trackwall will not support
the weight of the tool.
WARNING: To reduce the risk of serious personal
injury, ensure the fitting holding the hang hook
is secure.
WARNING: To reduce the risk of serious personal
injury, DO NOT suspend tool overhead or suspend
objects from the hang hook. ONLY suspend tool on the
Versatrack™ Trackwall using the hang hook.
WARNING: Ensure that the tool weight does not
exceed the maximum rated weight for the selected
Versatrack™ hook.
WARNING: When hanging objects on a Versatrack™
Trackwall rail, adequately space the tools in order to
not exceed 75 lb (35 kg) per linear foot.
CAUTION: Any product with exposed cutting teeth
must have them covered securely if it is to be on
the Versatrack™ Trackwall.
15 on the tool.
the tool.
English
7 .
7