Manuels Connexes pour Tuzio Rosendal
Sommaire des Matières pour Tuzio Rosendal
- Page 1 Tuzio Rosendal ® Towel Warmer Installation Guide Code: H8103 / H8104 10.5” x 37.5” Hydronic Technical Helpline: Toll-Free 1-877-757-8990 www.icocanada.com...
- Page 2 Congratulations! You are the proud owner of a quality Tuzio Towel Warmer. This product has been specifically engineered and tested to provide optimal comfort and satisfaction. ICO carries a broad range of luxury bathroom products designed to make everyday living just a little more enjoyable! Visit www.icocanada.com to learn more.
- Page 3 Towel Warmer Installation Procedure Rough-in Requirements - for constant circulation heating system (see figure 1) Using this installation method, the towel warmer is controlled using the valves attached to the towel warmer, and can be operated independently from the heating system. This method of installation is popular where there are multiple heating appliances connected to a closed hot water heating system, and electronic control of the individual towel warmer is not important.
- Page 4 Towel Warmer Installation Procedure Rough-in Requirements - for dedicated heating system (see figure 2) Using this installation method, the towel warmer is controlled using the thermostat wired to the circulator pump, and cannot be operated independently from the heating system. This method of installation is popular where there is only one heating appliance connected to a closed hot water heating system, and electronic control of the individual towel warmer is required.
- Page 5 Towel Warmer Installation Procedure Installation Instructions (see figure 3) 1. Check all items have been received. You should have Towel Warmer and mounting bracket kit. Read all instructions before continuing. 2. Fix wall supports "B" including collar “A” to the wall using the screws provided and in locations as shown on figure 2. 3.
- Page 6 Specifications & Drawings (wall rough-in) Model # Description Finish Weight (lb) Output WxH (mm) WxH (Inches) Metal Type H8103 Rosendal Hydronic Chrome 12.3 846Btu 266 x 950 10.5” x 37.5” Mild Steel 846Btu H8104 Rosendal Hydronic Brushed Nickel 12.3 266 x 950 10.5”...
- Page 7 Specifications & Drawings (floor rough-in) Model # Description Finish Weight (lb) Output WxH (mm) WxH (Inches) Metal Type H8103 Rosendal Hydronic Chrome 12.3 846Btu 266 x 950 10.5” x 37.5” Mild Steel H8104 Rosendal Hydronic Brushed Nickel 12.3 846Btu 266 x 950 10.5”...
- Page 8 Towel Warmers Electric In-Floor Heating Insulation Board...
- Page 9 ROSENDAL TOWEL WARMER INSTALLATION GUIDE E8103 / E8104 10.5” x 37.5” Plug-In 877-757-8930 www.icobath.com...
- Page 10 Towel Warmer Installation Procedure STEP 1 STEP 2 Rough-in Requirements (see figure 3) Installation Instructions (see figure 1) 1. A 110V receptacle located no further than 18” from 1. Check all items have been received. You should have electric plug-in exit location on towel warmer (see fig. received a towel warmer and mounting bracket kit.
- Page 11 Technical Drawing 4 x Robe Hook Figure 2 4 x Robe Hook Towel warmer contains a heat 75mm 75mm transfer solution 221/32 in which is non- 4 x mounting Towel warmer contains 4 x mounting brackets located toxic, an anti- brackets located a non-toxic heat at back of towel warmer...
- Page 12 Specifications Model Weight Element Output Metal Description Finish (lb) Size (BTU) (mm) (Inches) Type Rosendal E8103 Plug-In Chrome 21.6 150W 266 x 950 10.5” x 37.5” Mild Steel Rosendal Brushed Stainless E8104 Plug-In Nickel 21.6 150W 266 x 950 10.5” x 37.5”...
- Page 17 ROSENDAL TOWEL WARMER INSTALLATION GUIDE W8103 / W8104 10.5” x 37.5” Hardwired 877-757-8930 www.icobath.com...
- Page 18 Towel Warmer Installation Procedure STEP 1 STEP 2 Rough-in Requirements (see figure 3) Installation Instructions (see figure 1) 1. The incoming power feed goes to a deep single gang 1. Check all items have been received. You should have electrical box (for the controller). This electrical box received a towel warmer, hardwire kit, programmable can be located anywhere in the room, although we controller and mounting bracket kit.
- Page 19 Technical Drawing 4 x Robe Hook Figure 2 75mm 221/32 in Towel warmer contains 4 x mounting brackets located a non-toxic heat at back of towel warmer transfer solution, an anti-rust inhibitor and an anti-freeze Internal thermostat pre-set to 158of (fluid temperature) Electrical heating element 950mm Figure 4...
- Page 20 Specifications Weight Element Output Metal Model # Description Finish (lb) Size (BTU) (mm) (Inches) Type Electric W8103 Hardwire Chrome 21.6 150W 266 x 950 10.5” x 37.5” Mild Steel Electric Brushed Stainless W8104 Hardwire Nickel 21.6 150W 266 x 950 10.5”...