physa BARI GOLD Manuel D'utilisation page 5

Bari gold
1
a
d
b
c
7
2
6
5
3
4
1. control panel
A – orange (device in operation)
B – blue (a flashing icon – the device is off; icon
constantly on – the device is ready for use)
C – Red (maintenance, inspect the device)
D – green (working time indication)
2. ON / OFF switch
3. drainage hose (inside the device)
4. air filter
5. container
6. air nozzle
7. IR sensor
Use the ON / OFF switch to switch the device on. To use the
device, place hands in the drying zone and the machine
will start automatically and the orange light will come on
together with green diodes indicating the blowing time.
Once hands are removed from the opening, the device will
switch off automatically. The blowing time diodes will go
out gradually until the device turns off. In one mode, the
dryer will work for approx. 25 seconds and will switch off
automatically after that time. For the dryer to start again,
remove hands from the opening and re-insert them and
the operating mode will activate again. After use turn the
device off using the OFF switch. A flashing light and an
acoustic signal will indicate that the device has been turned
OFF. Drying time is approx. 7 seconds.
Oria white
1 2
10
9
ON/OFF
8
7
6
1. Drying time display
2. Control lights
3. Drainage hose (inside the device)
4. Air filter
5. Container
6. Housing
7. Operation sensors
8. Drying zone
9. Lights
10. ON / OFF switch
In order to turn the device in press and hold the ON/
OFF button until the device activates. To use the device,
place hands in the drying zone and the machine will start
automatically and the drying time will begin counting down
on the display from 10 to 0. Once the counter reaches 0,
the device will continue to operate for approx. 5 seconds
(a flashing „–" will be displayed) and then it will turn off.
If hands remain in the drying zone the dryer will activate
again once the „--" symbols stop flashing and come on
permanently. After hands have been removed from the
drying zone the device will switch off automatically. Drying
time is approx. 7 seconds.
After use turn the device off using the ON/OFF switch.
ATTENTION! The device has two air blowing modes: cold
and warm air. A green ON / OF button and POWER button
lights indicate a cold air mode, whilst blue means warm air.
To change from cold to warm air, or vice-versa, press and
hold the ON / OFF switch for approx. three seconds until
the button changes colour.
ASSEMBLING THE DEVICE
VELLA SILVER
Unscrew the two screws on the bottom of the device,
gently prize off the housing and remove it carefully.
Then disconnect the lead.
3
Align the device on the wall and mark the 4 places for
4
mounting screws. Drill holes, insert wall plugs, align the
device again and attach to the wall using mounting screws.
5 Then reconnect the lead and screw the housing on.
Rev. 14.09.2017
8
Bari gold
Drill 4 holes(30mm) in the wall.
Insert wall plugs into the holes.
Align and attach the mounting panel to the wall using 4
screws.
Run lead through the opening in the panel and hang
device on the panel.
Remove container and air filter. Use 2 screws to attach
device to the lower part of the panel. Insert air filter and
container.
Plug the power cable into a socket and switch the device
on.
Rev. 14.09.2017
Oria white
Align the device precisely at its
intended location, drill 4 holes and
attach mounting panel to the wall.
Attach the triangular bracket to the rear wall of the device
(with the narrow section pointing downwards).
Hang the dryer on the panel, align and attach the front
of the housing, screw triangular bracket to the wall, insert
container and air filter. Plug the power cable into a socket
and turn the device on.
10mm
350mm
ATTENTION! Do not mount the devices less than 350 mm
from the floor and less that 10 mm from the wall.
ATTENTION! Do not use the device without the container
and air filter.
Velox
Align the device precisely at its intended location, drill
3 holes and attach mounting panel to the wall.
Hang the dryer on the panel.
Screw the nut in the hole.
9