Page 1
ATTIS Series ATTIS 850R Bronze ATX Switching Power Supply 80PLUS Bronze efficiency certified Compliant with ATX 3.1 standards and supports up to 2X power excursion ▓ High efficiency with 80 PLUS Bronze certification ▓ 24/7 continuous power output with 50℃ operating temperature ▓...
Page 2
ATTIS ATTIS 850R Bronze SST-AT850R-BF ATX Switching Power Supply 80PLUS Bronze efficiency certified 850W This power supply is designed and manufactured according to the ATX 3 standard proposed by INTEL,This specification describes the requirements of 650W/750W Watts ;switching power supply with an stretch form-factor and ATX12V,,EPS12V.,+5V standby voltage, remote on/off control,full range line input...
Page 3
2.2 Load ranges 2.2.1 ( 850 Watts ) Parameter Nom. Unit +3.3V Amps Amps +12V 70.8 Amps -12V Amps +5VSB Amps ( 1 ) Maximum continuous total DC output power should not exceed 850W ( 2 )) Maximum continuous combined load on +3.3 VDC and +5 VDC outputs shall not exceed 100W.
Page 4
2.3.2 Definition The ripple voltage of the outputs shall be measured at the pins of the output connector when terminated in the load impedance specified in figure 1. Ripple and noise are measured at the connectors with a 0.1uF ceramic capacitor and a 10uF electrolytic capacitor to simulate system loading.
Page 5
2.7 Dynamic loading The PSU is subjected to a load change as shown in the table below at a rate of 1A/μsec (unless otherwise specified). The frequency of change is set to give the best readability of the deviation and setting time. All other output loads and the AC line voltage are chosen in order to obtain the worst case condition Load...
Page 6
4. PCIe* AIC Peak Power Duty Cycle test 4.1 Test Condition: Follow as below condition table. Duty Cycle Definition : Duty Cycle Test Criteria for a 850W PSU – RMS Time Constant Time for Power Duty Cycle (TC) Excursion (TE) Power @ TC Power @ TE 1900 μs...
Page 7
5. TIMING 5.1 Logical timing and control signals Parameter Description Required AC Power on Time T0<2s Power start time T1≤150mS Voltage rise time 0.2mS≤T2≤20mS PWR_OK Delay time T3≤150mS T4<10mS PWR_OK Rise time Ac power off maintenance time T5>16mS Power failure warning time T6>1mS 5.2 +5V and +3.3V timing requirements...
Page 8
5.2 Hold up time When the power loss its input power, it shall maintain 16ms in regulation limit at normal input voltage. Tested at 100% load 6. ENVIRONMENT 6.1 Operation Temperature 0 to 40 Relative Humidity 10 to 90%, non -condensing 6.2 Shipping and Storage Temperature -20 TO 70...
Page 9
A single PCIe 8pin cable and connector’s maximum current rating is Anschlusses beträgt 12,5 A, was 150 W (+12 V x 12,5 A) entspricht. 12.5A, which is 150W (+12V x 12.5A). So SilverStone’s warranty will not Daher deckt die SilverStone-Garantie keine Schäden oder...
Page 10
électrique asegúrese de que los dispositivos conectados funcionan dentro de estos límites. La garantía de SilverStone no cubrirá daños o fallos a Le courant nominal maximum d'un câble et d'un connecteur PCIe 8 resultas de un uso excesivo de estos conectores y sus cables broches unique est de 12,5 A, ce qui correspond à...
Page 12
Openings that do not exceed 5mm in any dimension Openings that do not exceed 1mm in width regardless of length...
Page 13
Model (safety certification):SST-AX0850FCBR-39L The equipment a Class | Switching Power Supply intended to use for information technology equipment or Audio and Video equipment. ※付属の電源コードは当該製品専用です。他の機器に使用しないでください。 Please refer to SilverStone website for latest specifications updates.