Télécharger Imprimer la page

Beaumont POSTE HOBBY SB230 Manuel D'utilisation page 2

Publicité

OPERATING INSTRUCTION
Type 125945010
In association with the installation and safety instructions for the
electric fencers
General Safety Instructions
Switch off the pasture fencer before coming into contact with it!
Operating manual information
The operating manual has some important instructions on handling the energizer. All technical details in the manual
have been prepared and compiled with the greatest possible care. Even so, errors cannot be excluded. We wish to point
out that we cannot assume any guarantee, legal responsibility or any liability for consequences attributable to possible lack
of details. We would, at all times, welcome any notification of possible errors. Safe working depends on the indicated safety
and handling instructions being adhered to. Also to be adhered to are those local accident prevention provisions which are in
force where the energizer is used as well as the general safety requirements.
The operating manual is to be studied carefully before any work begins!
As an integral part of the overall product it is to be securely kept right next to the energizer and for ease of consultation by
the personnel.
Do hand over this manual should this product be sold or passed on to another party. For a better understanding of what is
involved, some of the diagrams in this manual may not be true-to-scale and may deviate slightly from the actual construction-
al design.
1. Description and Construction of the Product
The energizer transmits voltage pulses to a connected pasture fence.
Caution! Only the optional additional parts prescribed by the manu-
facturer are to be used.
2. Installation
Installation:
The energizer can either be mounted on a wall or on a stable post. The
earthing rod (longitudinal rod) must be driven as deeply as possible into the
ground at a moist location and connected by a corrosion-resistant wire to the
earthing terminal ( ) of the energizer.
Connect the fence cable to the terminal with the lightning symbols ( ) .
The energizer is only protected against moisture if it is properly installed.
Shield the energizer from direct solar irradiation. Do not operate the energiz-
er when it lies on the ground. Set the energizer up in a location where there
is no fire hazard.
2
Earthing:
Good earthing of the fence is extremely important for trouble-free operation
and optimum performance of the energizer; therefore it should be earthed at
a preferably moist and overgrown location.
If the ground is dry and the fence is long, an additional earth conductor with
intermediate earths (every 50 m) should be installed along the fence.
CAUTION!
The energizer has an AUTO-ON function. As such, the energizer
starts following connection to the mains network.
3. Commissioning
Operation 12V :
Connect the controller to a 12V wet battery ( red + / black - ), ensure that the
terminals are absolutely clean and the polarity is correct. Use only rechar-
geable 12V- lead-acid batteries, during charging lead-acid batteries must
be placed in a well-ventilated area. After a few seconds a slight tic-tac can
be heard. The fence voltage level flashes with the pulses. In case of wrong
polarity the controller will not operate.
The battery should be recharged at a voltage of 11.9 volts (corresponding
to a discharge of approx. 60%). Do not discharge the battery deeper than a
voltage of 11.7 volts (corresponding to a disharge of approx. 80 %).
Operation 230V:
For the connection with mains (230V) use only the delivered Power
Supply 47PSU0009EU/UK or an alternative 47PSU0008EU/UK as indicated
on the front of the electric fence energizer.
After a few seconds a slight tic-tac can be heard. The fence voltage level flas-
hes with the pulses. In case of wrong polarity the controller will not operate.
Caution!
When using a solar system
Only carry out a battery or rechargeable battery test at start of the day ( no solar power supplied - cover panel )
6. Disassembly, Dismantling, Storage and Transport
Disassembly, Dismantling
Before starting disassembly:
● Switch off energizer
● Disconnect entire energy supply from the energizer.
● Remove operating/auxiliary materials and any remaining working materials and dispose of in an environmentally-compati-
ble manner.
Then properly clean sub-assemblies and parts and disassemble them in taking account of the local industrial safety &
environmental protection provisions in force.
85231A
3

Publicité

loading

Ce manuel est également adapté pour:

125945010