Publicité
Liens rapides
DIGITAL READOUT
For Mast-R-Lift Excel II
Model # 02230
Thank you for choosing this product from JessEm Tool
Company. We appreciate your support and hope that
our product serves you well. This product is designed
to provide many years of reliable service provided it is
used as intended and taken care of.
This user manual will assist you in assembly and
general operation of this product. It is not our intent
to teach you about woodworking. It is assumed that
you are an experienced woodworker with the basic
skills and experience necessary to use this product
safely. If after reading the following instructions, if
you are unsure or uncomfortable about safely using
this product we urge you to seek additional
information through widely available woodworking
books or classes.
As As part of our Continuous Product Improvement
Policy, JessEm products are always advancing in
design and function. Therefore there may be
differences between what is shown in our catalogs,
website or at retail display and what is sold at time of
purchase. We reserve the right to make positive
changes to our products at our discretion.
Step 1: Plug in one end of the CAT 5E
Shielded Cable into the bottom of the Digital
Readout Display assembly. (Figure 1)
Figure 1
All manuals and user guides at all-guides.com
61 Forest Plain Road,
Oro-Medonte, Ontario L3V 0R4
Canada
866-272-7492 Toll Free
705-726-8233 Local Phone
705-726-7519 Fax
Email: jessem@jessem.com
Website:
www.jessem.com
IMPORTANT!
Read and understand the contents of this
manual before assembly or operation of this
product.
Step 2: Attach the Digital Readout Display
Assembly to the back right of your Excel II
table top using the (4) 10-24 x ½" Torx
drive screw. (Figure 2)
Figure 2
Publicité
Sommaire des Matières pour JessEm Tool 02230
- Page 1 For Mast-R-Lift Excel II Model # 02230 61 Forest Plain Road, Oro-Medonte, Ontario L3V 0R4 Thank you for choosing this product from JessEm Tool Canada Company. We appreciate your support and hope that 866-272-7492 Toll Free our product serves you well. This product is designed...
- Page 2 All manuals and user guides at all-guides.com Step 3: Attach the Magnet Clamp Assembly to the carriage. Note the position in Figure 3 and tighten the ¼-20 Cap Screws with the 3/16 hex key. Figure 5 Step 6: Install two (2) “AAA” Batteries (not included) into the display.
- Page 3 All manuals and user guides at all-guides.com AFFICHAGE NUMÉRIQUE pour le Mast-R-Lift Excel II 61 Forest Plain Road, Oro-Medonte, Ontario L3V 0R4 Merci d'avoir choisi ce produit de la compagnie JessEm Canada Tool. Nous apprécions votre soutien et nous espérons 866-272-7492 Appel gratuit que ce produit vous sera très utile.
- Page 4 All manuals and user guides at all-guides.com Étape 3: Attachez la fixation magnétique au chariot. Regardez la position sur l'image 3 et resserrez les vis ¼-20 avec une clé hexagonale 3/16. Image 5 Étape 6: Installez les deux (2) batteries AAA (non- incluses) dans l'affichage (Image 6).
- Page 5 All manuals and user guides at all-guides.com TROUBLESHOOTING RÉSOLUTION DE PROBLÈME Readout Issues: Problèmes d'affichage: Unstable constantly scrolling numbers: Constamment instable pendant le défilement des chiffres: • Insure the sensor is properly installed on the scale. • S'assurer que le capteur est correctement installé sur l'échelle.
- Page 6 All manuals and user guides at all-guides.com Accuracy Issues Problèmes de précision Petites erreurs de précision de 1/16” ou moins: Small accuracy errors of 1/16” or less: • S'assurer que les becs sont bien serrés et à plat • Be sure the jaws fit tight and flat when in use and pendant l'utilisation et lors du calibrage.
- Page 7 All manuals and user guides at all-guides.com...
- Page 8 All manuals and user guides at all-guides.com...