Initial Settings - Insignia NS-30HTV Guide De L'utilisateur

When your TV receives a digital signal, the
digital information appears.
51-3 M o o n S t a r
CITYHD
Remaining Time 0:20 TV-Y7
No program information is available.
• Broadcast program name
• Station name
• Remaining time
• Audio language
• Program name
• V-CHIP RATING
• HD or SD mark
• Closed Caption mark
• V-Chip mark
2 Press DISPLAY again, the analog
information appears.
S T E R E O
S A P
T V- P G L V
O N T I M E R 8 : 3 0 A M
O F F T I M E R 1 1 : 3 0 P M
S L E E P T I M E R 2 h 0 0 m
F U L L
C L O C K 1 2 : 0 0 A M S U N
• Clock
• Channel number or VIDEO mode
selected
• Channel label (if preset)
• Stereo or SAP (second audio program)
audio status
• Content rating
• On timer, Off timer, Sleep time (if preset)
• Picture size
Note When your TV receives an analog signal,
DISPLAY shows only analog information.
3 Press DISPLAY again to clear the display.
To set the sleep timer:
1 To set your TV to turn off after a preset
amount of time, press SLEEP on the remote
control. The clock adds 10 minutes to the
interval each time you press the SLEEP
button.
After the sleep time is programmed, the
display appears briefly every ten minutes to
remind you that the sleep timer is operating.
2 To confirm the sleep timer setting, press
SLEEP and the remaining time is displayed
for a few seconds.
3 To cancel the sleep timer, press SLEEP
repeatedly until the display turns to 0h00m.

Initial settings

This section describes the initial settings you
must make when you turn on your TV for the first
time.
10
SUN Jan 01 12:00 PM
English
HD CC
A N T
A B C D
C A B L E
7
www.insignia-products.com
Selecting the language
You can select English, Spanish, or French for
the menu language displayed on the screen.
To select your language:
1 Press MENU on the remote control. The
menu screen opens.
2 Press or
The SETUP menu screen opens.
SETUP
LANGUAGE
CLOCK SET
TV/CABLE
AUTO CH MEMORY
ADD/DELETE
:SELECT
3 Press or
S E T U P
L A N G UAG E
E N G L I S H
C L O C K S E T
T V / C A B L E
AUTO CH M E MO RY
A D D / D E L E T E
: S E L E C T
4 Press or
want.
5 Press EXIT on the remote to return to normal
viewing.
Memorizing channels
Your TV is equipped with a channel memory
feature which allows channels to skip up or down
to the next channel set into memory, skipping
over unwanted channels. Before selecting
channels, they must be programmed into your
TV's memory. Your TV can receive up to 250
VHF/UHF channels and 500 cable TV channels.
To use your TV with an antenna, set the TV/
CABLE menu option to the TV mode. When
shipped from the factory, this menu option is in
the CABLE mode.
To select TV or Cable mode:
1 Press MENU on the remote control. The
menu screen opens.
2 Press or
The SETUP menu screen opens.
SETUP
LANGUAGE
CLOCK SET
TV/CABLE
AUTO CH MEMORY
ADD/DELETE
:SELECT
3 Press or
4 Press or
• TV – VHF/UHF channels
• CABLE – Cable TV channels
to select the setup icon
ENGLISH
CABLE
:ADJUST
to select LANGUAGE.
E N G L I S H
/ F R A N Ç A I S / ES PA Ñ O L
C A B L E
: A D J U S T
to select the language you
to select the setup icon
ENGLISH
CABLE
:ADJUST
to select TV/CABLE.
to select TV or CABLE.
.
.