Publicité
Universal compatibility with T50, up to 14 mm.
1. Pinch the magazine release clip
sliding magazine
5
.
2. Load fasteners. Ensure staples are loaded so that crown of
the staples sits against inside surface of the magazine.
nOTE: The head of the brad nail must sit against the left,
inside surface of the magazine. If loaded on right side the
magazine will not close.
3. Close sliding magazine until the magazine latch
clips snuggly in place.
Unloading the Tool (Fig. A, C)
WARNING: Always ensure the power switch is in the
off (0) position.
1. Pinch the magazine release clip
sliding magazine
5
.
2. Tip the tool to the side until the staples slide freely out of
the bottom of the magazine.
3. Check to ensure no loose staples remain inside magazine.
4. Close sliding magazine fully.
Clearing a Jammed Staple (Fig. A, C)
If a staple becomes jammed in the magazine, keep the
tool pointed away from you and follow these instructions
to clear:
1. Pinch the magazine release clip
loaded staples.
2. Visually check inside magazine
staples.
3. Remove bent staple using pliers if necessary.
4. Reinsert staples into magazine (see Loading the Tool)
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and keep away from the
trigger before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Trigger Operation (Fig. A, D)
WARNING: Always wear proper eye [ANSI Z87.1 (CAN/
CSA Z94.3)] and ANSI S12.6 (S3.19) hearing protection
when operating tool.
The BLACK+DECKER cordless staplers are assembled in
accordance with the ANSI Standard SNT‑101‑2002.
WARNING: Keep fingers AWAY from trigger when not
driving staples to avoid accidental fastener discharge.
NEVER carry tool with finger on trigger.
1. Push the power switch
stapler n.
2. Fully depress contact trip
the green indicator
3
3. Pull trigger
1
(fastener will drive into work surface
nOTE: Maintain downward pressure on work surface until
the fastener is driven into the work surface.
6
and pull out the
6
and pull out the
6
and remove any
5
for any jammed
2
from "O" to "I" to turn
against the work surface and
4
should light up.
4. Release trigger.
5. Lift contact trip off work surface.
6. Repeat steps 1 through 4 for next application.
nOTE: The contact trip needs to be depressed followed by
a trigger pull for each fastener followed by a release of both
the contact trip and trigger after each fastener.
Proper Hand Position (Fig. E)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off, allow motor to stop, and
keep away from power switch before making
any adjustments or removing/installing
attachments or accessories. An accidental start‑up
can cause injury.
Your BLACK+DECKER power tool has been designed to
operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those
offered by BLACK+DECKER, have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
BLACK+DECKER recommended accessories should be
used with this product.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service
center. If you need assistance in locating any accessory, please
contact BLACK+DECKER call 1‑800‑544‑6986.
Universal compatibility with T50, up to 14 mm.
Repairs
The charger and battery pack are not serviceable. There are
no serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
English
7
Publicité
