Space Seating 25004 Instructions De Montage

ÉTAPE 1 ÉTAPE 2
13
2
x5
1
9
8
ÉTAPE 4 ÉTAPE 5
13
11
x3
12
4
6
Enlever toutes les pièces du carton, les organiser selon les numéros de pièce indiqués sur la liste et vérifier que les quantités des pièces
reçues sont correctes.
ÉTAPE 1 Insérer les cinq roulettes (2) dans la base (1). Pousser fermement jusqu'à ce que les roulettes (2) s'encliquettent.
ÉTAPE 2 Fixez les bras (7L & 7R) au coussin de siège (5) en utilisant trois rondelle plates (8) et trois vis su bras (9) pour chaque bras.
SERREZ TOUTES LES VIS AVEC LA CLÉ ALLEN (13).
ÉTAPE 3 Attachez le mécanisme (4) au coussin de siège (5) avec la flèche vers l'avant de la chaise, en utilisant quatre vis du mécanisme (10).
SERREZ TOUTES LES VIS AVEC LA CLÉ ALLEN (13).
ÉTAPE 4 Fixer le support du dossier (12) à l'arrière du mécanisme (4) à l'aide trois vis du dossier (11).
SERREZ TOUTES LES VIS AVEC LA CLÉ ALLEN (13).
ÉTAPE 5 Insérer le vérin pneumatique (3) dans la base (1). Placer le siège assemblé sur le dessus du vérin pneumatique (3) et pousser vers le bas.
ATTENTION: AVANT D'UTILISER LE FAUTEUIL, S'ASSURER D'AVOIR SERRÉ COMPLÈTEMENT TOUTES LES VIS.
25004 / 27008
FAUTEUIL DE DIRECTION
INSTRUCTIONS DE MONTAGE
ÉTAPE 3
13
9 x3
10
x4
x3
x3 8
x3
4
5
7L
7R
5
PIÈCE
1. Base . . . . . . . . . . . . . . . . . . . . . . . . . . .1
2. Roulettes . . . . . . . . . . . . . . . . . . . . . . . .5
3. Vérin pneumatique . . . . . . . . . . . . . . . . .1
4. Mécanisme. . . . . . . . . . . . . . . . . . . . . . .1
5. Coussin du siège . . . . . . . . . . . . . . . . . .1
6. Dossier. . . . . . . . . . . . . . . . . . . . . . . . . .1
7. Bras (7L et 7R) . . . . . . . . . . . . . . . . . . . .2
8. Rondelle plates . . . . . . . . . . . . . . . . . . . .6
9. Vis du bras . . . . . . . . . . . . . . . . . . . . . . .6
10. Vis du plaque du siège . . . . . . . . . . . . .4
11. Vis du dossier . . . . . . . . . . . . . . . . . . . .3
3
12. Support du dossier (pre-installed). . . . . .1
13. Clé Allen. . . . . . . . . . . . . . . . . . . . . . . .1
© Office Star Products novembre, 2022
4
QTÉ
1
SPACE LIMITED WARRANTY
SPACE® chairs are warranted* from the date of purchase against failure due to material and workmanship as follows:
• Lifetime on component parts including pneumatic cylinder, control mechanism, base and casters.
• 3 Years on upholstery fabric and foam against wear and deterioration.
• Leather is not warranted against routine scratching and scuffing, as leather is subject to minor blemishes in.
To make a warranty claim, contact Parts Department. Provide model number, proof of purchase, description of the problem and obtain return authorization. At it's
option Office Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer's component. The customer must prepay freight on any components returned to the factory. Return freight on
components still in warranty will be paid by Office Star Products.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 250 lbs.
or less. The 63-37A773HM, 75-7A773, 75-37A773, 75-47A773 and 839-11B35WA are for persons weighing 400 lbs. or less, the 818 & select 829's with
selfadjusting mechanism are 300 lbs. or less and the 15-37A720D is 325 lbs. or less. This warranty will not cover labor, freight or damage from misuse, abuse,
negligence, alteration, accident, vandalism, rusting, acts of nature or any other event beyond the control of Office Star Products. The warranty does not cover
cosmetic damage that may result from normal use. Liability for incidental or consequential damages is excluded. The user assumes all risk of injury resulting
from use of this product. When usage is more than 40 hours per week, a five year warranty on all parts applies. Fabric is warranted for one year. This warranty
gives you specific legal rights, and you may also have other rights which vary from state to state.
All Work Smart chairs are built to meet or exceed ANSI BIFMA standards.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts are damaged or missing. Our
Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail parts.department@officestar.net, by Fax 1-909-930-5629, or
toll free parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 3:30pm. Pacific Time.
25004 / 27008
MANAGER'S CHAIR
OPERATING INSTRUCTIONS
FEATURES
• PNEUMATIC SEAT HEIGHT ADJUSTMENT
To raise seat, remove pressure from seat and pull lever (1) up. To
lower seat, sit on chair and pull lever (1) up.
NOTE: It is normal for chair to slightly lower under body weight.
• MID-PIVOT KNEE TILT ADJUSTMENT
To adjust tilt angle, pull lever (2) up for free float, and push lever (2)
down to lock into any position.
• TILT TENSION ADJUSTMENT
To adjust tilt tension, turn knob (3) counter-clockwise to increase
tension, and turn knob (3) clockwise to decrease or ease tension.
NOTE: Be careful not to loosen back tilt adjustment knob completely.
• ARM HEIGHT ADJUSTMENT
To adjust arm height, push button (4) in to allow the arms to move
up or down freely. Release the button (4) once the desired height is
reached.
WARNING
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and knobs are
securely tightened.
3. Check that all bolts screws and knobs are tight every three months or
as needed.
4. Do not overturn back tilt knob when decreasing tension.
5. Dispose of packing material properly. Do not use plastic cover as head
3
covering. It may cause suffocation.
6. Do not use chair as a stepladder.
7. Use this chair for its intended purpose only.
8. Use mild detergent only for cleaning.
2