Télécharger Imprimer la page

Pahlen 125933 Mode D'emploi page 4

Publicité

Main drain
Item no. 125933 (for pool with liner) and 125938 (for concrete pool)
Technical specifications:
Installation
Place the drain according to the instructions from your pool supplier.
If the drain is placed in the bottom of the a pool with liner and a floor of sand the drain must be fixed with concrete.
NOTE! Minimum distance between stainless steel material and non-stainless (e.g. Concrete-reinforcing bars) will be 50 mm.
If the drain is placed in a pool together with for exampel a waterfall, 2 pcs of the drain must be mounted with at least 2 meters
between them (for safety reasons).
Installation in a pool with liner
Mount the drain flange in line with the finished pool layer, se picture1.
Mount the self-adhesive gasket on the drain flange. After the liner is in place,
mount the front frame with a gasket behind. Cut out for the drain opening in the
liner. Mount the grille.
Installation in a concrete pool
As additional accessories there are clamps (item no. 112900) to stabilize the
drain in the concrete and non leak flanges (item no.121953) for connection/pipe
entry. Use suitable thread sealing.
For swimming pools with liner and sand bottom the drain must be fixed with concrete.
Before casting, mask off the drain flange and the opening to avoid stains from
concrete splashes.
Mount the drain flange in line with the finished pool layer.
Place the drain in the mould and cast.
Mount the grille afterwards.
10
2"
internal
Picture 2
thread
Item no. 125938
1. Skimmer
2. Light
3. Jet Swim
4. Inlet
5. Drain
6. Check valve
7. Pump
8. Filter
9. Electric heater
10. Drain
Picture 3
Recommended values for
water quality
Chlorine content:
max 3.5 mg/l
Chloride (salt) content: max 250 mg/l
pH-value:
7.2  – 7.6
Alkalinity:
60  – 120 mg/l (ppm)
Calcium hardness:
100  – 300 mg/l (ppm)
Iron:
max 0.1 mg/l *
Copper:
max 0.2 mg/l *
Manganese:
max 0.05 mg/l *
Phosphorus:
max 0.01 mg/l *
Nitrate:
max 50 mg/l*
Max. flow capacity: 20 m
/h
3
2
11
1
7
VISE
Outside these values the product warranty does not apply.
Picture 1
Item no. 125933
4
6
8
9
internal
thread
12
Installation elvärmare Aqua HL line
Surface treatment
E
+/-
The tolerance class in accordance with this
3
part of ISO 2768-1
2
5
Box 728, SE-194 27 Upplands Väsby, Sweden
Phone +46 8 59411050, Fax +46 8 59086880
8
10
4
ENGLISH
2"
1. Screw M5x20 (2x)
2. Grille
3. Screw M5x16 (12x)
2"
4. Front frame
Surface treatment
external
E
The tolerance class in accordance with this
5. Gasket
thread
part of ISO 2768-1
6. Liner
Box 728, SE-194 27 Upplands Väsby, Sweden
7. Self-adhesive gasket
Phone +46 8 59411050, Fax +46 8 59086880
8. Foam
9. Poolwall
10. Screw M5x16 (2x)
11. Clamps (4x)
12. Non leak flange
4
Designed by:
Drawn by: Date
ASA 2014-11-21
Assembly drawing no.
Art.no.
Scale
Installation betong
2
Drawing number
Bottenavl djupt betong MA55 29
6
9
Drawing no: M10690-7
* Complies with EN 16713-
1
2
3
5
7
Designed by:
Assembly drawing no.
Installationsbild bräddavlop
för pool med duk
Approved by:
Revised by: Date
Rev.no.
2022-05-31 ASA

Publicité

loading

Ce manuel est également adapté pour:

125938