Publicité
Liens rapides
INSTALLATION and SERVICE INSTRUCTIONS
NOTE
For LTUL Models, Form "C" contacts on timer, Rated 30 VDC 3A, the enclosed timer is to be used
and installed per the enclosed LT-1UL installation sheet. LTUL Models, Form "C" contacts on timer,
Rated 30 VDC 3A maximum rating 30 VDC 3A. For access control installations, power for the LT-1
Timer must be supplied by a power source listed to UL294. When used for access control, this device
shall be used as part of an access controlled egress door system. It is up to the local AHJ to allow
use of this device in place of an automatic sensor. For higher security installations, lower time limits
should be used.
REMARQUE
Pour les modèles LTUL Models, Form "C" contacts on timer, Rated 30 VDC 3A, la minuterie intégrée
doit être installée et utilisée suivant la fiche d'installation LT-1UL fournie. La cote maximale des
modèles LTUL Models, Form "C" contacts on timer, Rated 30 VDC 3A est de 30 VCC 3A. Pour les
installations de contrôle d'accès, l'alimentation de la minuterie LT-1 doit être fournie par une source
homologuée UL294. Lorsque cet appareil est utilisé aux fins de contrôle d'accès, il doit faire partie
d'un système de porte de sortie à accès contrôlé. Il incombe donc à l'AHJ local d'autoriser l'utili-
sation de cet appareil au lieu d'un capteur automatique. Pour les installations de sécurité plus ren-
forcée, des délais inférieurs doivent être utilisés.
SWITCH RATING
2 Form C Contacts
125/250 VAC, 10A, ½ HP
30 VDC, 6A
EMERGENCY STOP
We protect the things that protect you. ®
LTUL Models
Form "C" Contacts on Timer
Rated 30 VDC 3A
Publicité
Sommaire des Matières pour Warming Trends EMERGENCY STOP
- Page 1 EMERGENCY STOP INSTALLATION and SERVICE INSTRUCTIONS NOTE For LTUL Models, Form “C” contacts on timer, Rated 30 VDC 3A, the enclosed timer is to be used and installed per the enclosed LT-1UL installation sheet. LTUL Models, Form “C” contacts on timer, Rated 30 VDC 3A maximum rating 30 VDC 3A.
- Page 2 HOUSING INSTRUCTIONS PROCEDURE Pull bottom of housing out and lift up until tabs are released from slots in top of switch assembly. Once complete, secure cover with screw and hex wrench (shown). WIRE CONNECTIONS PROCEDURE Pull bottom of housing out and lift up until tabs are released from slots in top of switch assembly.
- Page 3 INSTALLATION * BUTTON ILLUMINATION WIRING 12-24 VAC/VDC, 21mA EACH COLOR BLACK - GROUND WHITE - WHITE LED (+) GREEN - GREEN LED (+) RED - RED LED (+) NOTE ADA mounting compliance requires the operable part of the initiating device shall not be less than 1.1 M (3 ½...
- Page 4 PRODUCT DIMENSIONS WIRE CONNECTIONS Stopper Station button is configured as ordered. If needed, installer can reconfigure function to: Key-to-Reset, Momentary, or Turn-to-Reset.
- Page 5 CHANGING PUSH BUTTON FUNCTION PROCEDURE Remove contact block screws from mounting plate. To change button function remove the plate and use directions provided. Reassemble backplate and contact box (ensure contact tabs are facing up as shown). If reconfiguring from Turn-to-Reset, remove Turn-to-Reset label.
- Page 6 BUTTON FUNCTION SET-UP: KEY-TO-RESET PROCEDURE Remove stop pin from position shown. Once pin is removed, reset ring will rotate clockwise as shown above. Replace stop pin in right hole. Call STI for wedge block if original configuration is Turn-to-Reset. If converting from Turn-to-Reset or momentary, call STI for key (KIT-H18061).
- Page 7 BUTTON FUNCTION SET-UP: KEY-TO-RESET PROCEDURE Remove wedge block. Remove stop pin from right hole. Reset ring will rotate clockwise as shown. Place stop pin in left hole. If converting from either momentary or Key-to-Reset, call STI for reset label (L16210).
- Page 8 à l’ensemble du personnel chargé de l’essai et de l’entretien de ce produit. Les boutons poussoirs pour utilisation à l’extérieur doivent être installés avec couvercles pour l’extérieur de STI. CONTACT WARMING TRENDS 1050 W. Hampden Avenue, Suite 200 orders@Warming-Trends.com Englewood, CO 80110 303.346.2224...