Publicité
FIRE-FIGHTING SAFETY MEASURES
When installing the appliance, the following safety measures must be observed:
a)
In order to ensure sufficient thermal insulation, respect the minimum safety distance from objects or furnishing components
flammable and sensitive to heat and from materials with flammable structure (see CE MARKING INFORMATION -
All the minimum safety distances are shown on the product data plate and lower values must not be used.
b)
in front of the furnace door, in the radiation area, there must be no flammable or heat-sensitive objects or material at a distance
of less than 80 cm. This distance can be reduced to 40 cm where a rear-ventilated, heat-resistant protection device is installed
in front of the whole component to protect;
c)
If the product is installed on a no totally refractory floor, one must foresee a fireproof background. The floors made of
inflammable material, such as moquette, parquet or cork etc., must be covered by a layer of no-inflammable material (size
according to regional law, see
The ash drawer must always be inserted when the appliance is in operation.
The solid combustion residues (ashes) must be collected in a metal container that is hermetically sealed and fire resistant. The
appliance must never be lit in the presence of gaseous emissions or vapours (for example: glue for linoleum, petrol, etc,). Do not place
flammable materials in the vicinity of the appliance.
During the combustion, thermal air is emitted by involving the heating of areas, door and glass hearth, of the door handles
or controls, of the smokes pipe and, in case, of the front part of appliance. Avoid to touch those parts without a protective
clothing or without accessory tools (gloves resistant to heat, control devices). Ensure children are aware of these
dangers and keep them away from the furnace when it is on.Warn children that the device becomes very hot and
that it must not be touched.
When using the wrong fuel or one which is too damp, due to deposits present in the flue, a flue fire is possible.
FIRST-AID MEASURES
Should any fire arise in the stack or in the flue:
a) Close the feeding door.
b) Close the registers of combustion air
c)
Extinguish the fire using carbon dioxide fire-fighting means (CO
d) Seek immediate intervention of FIRE BRIGADE.
DO NOT ExTINGUISH FIRE USING WATER JETS. When the flue does not burn any more please arrange an examination by a
specialist in order to find possible cracks and permeable points.
BEAM PROTECTIONS
Considering the irradiation of the hearth, it is necessary to be particularly careful in protecting the beams while designing your stack.
Consider the proximity of beams to the external surfaces of the hearth, on one side, and the irradiation of the glass door, usually very
close to the beams, on the other side. In any case, it has to be considered that the internal or lower surfaces of this beam in flammable
material must not come in contact with temperatures higher than 65 °C.
WARNING: We cannot be made liable for a wrong operation of the plant, when it does not comply with the provisions
of these instructions or when it uses additional products not suitable for this device.
TECHNICAL DESCRIPTION
Definition: product according to EN 13240 The appliance works as an intermittent operating appliance.
The appliance is made up of a series of cast-iron elements joined to one another by a fixed joint, while the seal is assured by
refractory putty. The assembly is supported by tie rods and nuts located outside the heating body and coated with a carter made of
varnished and galvanized sheet heat-resistant.
The appliances are equipped with an integrated air circuit for the recovery of the heat made up of deflectors (radiant fins) on all
external surfaces of the heating body. The appliances are equipped with a hearth with double thickness part.
The insert is equipped with a sight door with ceramic glass (resistant up to 700°C). This allows a charming sight on burning flames.
Moreover, in this way, any possible leak of sparks and smoke is avoided. Under the hearth grating there is a easily extractable ash
drawer, also when the appliance works.
ACCESSORIES
The heating of the room occurs:
a)
by convection: the passage of air through the coating and the covering hood releases heat in the room.
b)
by radiation: through the sight glass and the steel body, heat is radiated into the room.
The device is equipped with registers of primary and secondary air, with which it is possible to adjust the combustion air.
1A - PRIMARY air register
With the air register located under the door of the hearth (on the left), it is possible to adjust the air flow through the ash drawer
and the grating in direction of the fuel. The primary air is necessary for the combustion process during the ignition. When the
Picture
1).
POKER
SERIES
(Picture
8)
dust).
2
Picture 2
gives some examples of execution.
GLOVE
SERIES
ENgLIsH
Picture
7).
21
Publicité
