Publicité
■
Ensure that cables are not pinched, kinked or damaged by sharp edges.
■
Always lay cables so that nobody can trip over or become entangled in them. This poses
a risk of injury.
5.7 Connected devices
■
Also observe the safety and operating instructions of any other devices which are con-
nected to the product.
5.8 Product
WARNING
Risk of electric shock!
Always disconnect the product from the mains power supply before con-
nection, disconnection, cleaning, or troubleshooting.
6 Product overview
1
2
3
1
Mains plug
3
Inlet: suction port
5
Base
7 Installation location
WARNING
Risk of electric shock!
Never locate the product in water or areas prone to flooding.
Note:
It is recommended to use a pre-filter and suction equipment consisting of a suction hose,
a suction strainer and a non-return valve. This will prevent damage to the pump from
stones and other solid foreign objects.
■
Install the pump on a flat, level, stable, surface.
■
The product should only be installed in an upright position.
■
The product is only suitable for fixed installations and must be fastened to the surface via
the base mounting points.
■
Provide the necessary space around the pump for heat dissipation, inspections and ser-
vicing.
8 Installation and connection tips
If in doubt about how to install a pump system correctly, contact a qualified pro-
fessional.
■
The pump suction line must be larger than the pressure line.
■
The suction line must be able to withstand the maximum pump pressure.
■
Apply sealing tape on threaded connections.
■
Do not over-tighten connections to prevent damage to fittings.
■
The pipe weight should be supported independently and not by the pump.
5
4
5
2
Outlet: pressure port
4
Motor cover
■
High suction lifts or long suction lines might need extra time and can impact perform-
ance.
■
If the water contains sand or debris, install a pre-filter to avoid pump clogging and dam-
age.
■
Install a water inlet valve or non-return valve on the pump suction line to prevent it from
emptying after use.
■
Position the water inlet deep enough to avoid air intake when water levels drop.
9 Operation
NOTICE
Risk of damage to product!
The pump must never be allowed to run dry.
9.1 Switch the power ON
1. Connect the mains plug to a mains power supply.
2. Wait a few moments for the pump to start delivering water. If flow does not start within
ten minutes, stop the motor and determine cause. See section:
9.2 Switch the power OFF
1. Disconnect the mains plug from the power supply. See section:
[} 5].
10 Removal from service
Important:
If the pump is not going to be used for a long time or there is risk of frost, empty it com-
pletely and allow it to dry.
1. Disconnect the mains cable from the power supply.
2. Disconnect all hoses from the product and air dry.
3. Drain any remaining water from the product and air dry.
11 Clearing blockages
You can try to clear any blockages by forcing water through the system.
1. Switch the power OFF.
2. Disconnect the mains cable from the power supply.
3. Connect the pressure line to the water line.
4. Remove the intake hose.
5. Briefly open the water pipe and let water run through the pump.
12 Cleaning and repairs
12.1 Cleaning
Important:
– Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions.
They damage the housing and can cause the product to malfunction.
– Do not immerse the product in water.
1. Disconnect the product from the power supply.
2. Clean the product with a fibre-free cloth.
12.2 Repairs
Never open the motor housing. Any repair work must be carried out by a qualified
professional.
13 Troubleshooting
Problem
Possible cause
Product does
No power.
not switch ON.
Pump draws in
Contaminated water.
too little water or
Suction hose/pre-filter
no water at all.
clogged.
Filter basket clogged.
Suction hose damaged.
Suction hose material too
soft/thin.
Suction hose not deep
enough in the water.
Suction port not sealed.
Troubleshooting
[} 5].
Removal from service
Suggested solution
Check the power supply.
Disconnect plug from mains socket. Wait 10
seconds and connect to mains socket again.
Clean pre-filter.
Rinse suction hose with water. Clean the
pre-filter (if applicable) .
Rinse and clean the filter basket (if applic-
able).
Replace suction hose.
Use stiffer/thicker suction hose.
Suction valve must be at least 10 cm below
the water surface.
Seal suction port with sealing tape.
Publicité
