Hubbell LNC4 Instructions D'installation

INSTALLATION INSTRUCTIONS - LNC4
WARNING! Fixtures must be grounded and installed in accordance with the National Electrical Code and all local codes. Failure to do so may increase the RISK OF PERSONAL
INJURY, PROPERTY DAMAGE, FIRE AND DEATH. Install and use so fixture failures do not cause a hazard and use only in environments for which the product is specifically
marked.
WARNING! This product contains chemicals known to the State of California to cause cancer, birth defects, and/or other reproductive harm. Thoroughly wash hands after
installing, handling, cleaning, or otherwise touching this product.
CAUTION! Follow ALL luminaire recommendations, product markings, instructions, restrictions and warnings regarding lumninaire operation and burning position. Luminaire label
shows electrical and environmental requirements and restrictions.
All electrical work must be done by a qualified electrician.
Turn off electric power to all affected circuits and allow to cool before servicing.
A regularly scheduled maintenance program should be established to retain optimum light output and reduce heat retention. Dusting with a soft, clean, dry cloth is normally
sufficient for the optical system. Any accumulation of dust or dirt should be removed regularly.
Carefully read these instructions before installing product. If you do not understand these instructions, before starting any work, contact your Hubbell Lighting distributor or
techsupport@hubbell-ltg.com or (864) 678-1000
Give instructions to facility owner/manager for future reference.
TOOLS REQUIRED: (NOT INCLUDED) ANY TOOLS NEEDED FOR APPROPRIATE WALL FASTENERS, 1/8" ALLEN WRENCH FOR SET SCREWS, PHILIPS HEAD SCREW
DRIVER
PARTS REQUIRED: (NOT INCLUDED) SILICONE CAULK, WALL ANCHORS AND FASTENERS APPROPRIATE FOR WALL CONSTRUCTION TYPE
FIXTURE MOUNTING WITH JUNCTION BOX
1. ATTACH MOUNTING PLATE (ITEM 1) TO RECESSED JUNCTION BOX (ITEM 2) USING APPROPRIATE HARDWARE
(SUPPLIED BY OTHERS.) WARNING! INSTALLER IS RESPONSIBLE FOR ENSURING THE FIXTURE IS PROPERLY
ATTACHED AND SEALED TO THE JUNCTION BOX. DEPENDING ON THE WALL TEXTURE AND INSTALLATION
JUNCTION BOX, CAULK MAY NEED TO BE APPLIED TO PREVENT WATER FROM GETTING INTO JUNCTION BOX.
2. PULL WIRES THROUGH GASKET AND MOUNTING PLATE.
3. WIRE SERVICE LEADS TO FIXTURE POWER LEADS ACCORDING TO LOCAL AND NATIONAL ELECTRICAL CODES.
CONNECT GROUND WIRE TO GREEN WIRE. CONNECT BLACK TO BLACK AND WHITE TO NEUTRAL THEN PUSH
CONNECTIONS BACK INSIDE THE JUNCTION BOX (ITEM 2) .
4. HOLD FIXUTRE AT A SLIGHT ANGLE SLIDING THE ANGLED POINTS OF THE MOUNTING PLATE INTO THE
MATCHING SLOT ON THE BACK HOUSING AND ROTATE THE FIXTURE DOWN OVER THE MOUNTING PLATE.
5. ENSURE THAT NO WIRES ARE BEING PINCHED OUTSIDE OF THE FIXTURES AND TIGHTEN THE TWO SET
SCREWS (ITEM 3) UNTIL FIXTURE IS SECURELY FASTENED.
ITEM 7
ITEM 5
93069465 Rev. A
701 Millennium Boulevard Greenville, SC 29607 (864) 678-1000
All manuals and user guides at all-guides.com
SAVE THESE INSTRUCTIONS
ITEM 4
ITEM 7
ITEM 6
ITEM 5
MOUNTING PLATE LAYOUT
FIXTURE MOUNTING WITH CONDUIT
1. REMOVE REAR HOUSING (ITEM 4) FROM FIXTURE BY REMOVING 4 FRONT HOUSING SCREWS (ITEM 5)
AND 7 COVER SCREWS (ITEM 6).
2. MOUNT THE REAR HOUSING TO THE JUNCTION BOX BY FOLLOWING THE SAME STEPS LISTED FOR
"MOUNTING FIXTURE TO JUNCTION BOX".
FIXTURE IS PROPERLY ATTACHED AND SEALED TO THE JUNCTION BOX. DEPENDING ON THE WALL
TEXTURE AND INSTALLATION JUNCTION BOX, CAULK MAY NEED TO BE APPLIED TO PREVENT
WATER FROM GETTING INTO JUNCTION BOX.
3. REMOVE NECESSARY CONDUIT PLUGS. CONDUIT PLUGS (ITEM 7) ARE LOCATED ON THE TOP,
BOTTOM, AND EACH SIDE OF THE REAR HOUSING.
4. WIRE SERVICE LEADS TO FIXTURE POWER LEADS ACCORDING TO LOCAL AND NATIONAL
ELECTRICAL CODES. CONNECT GROUND WIRE TO GREEN WIRE. CONNECT BLACK TO BLACK AND
WHITE TO NEUTRAL THEN PUSH CONNECTIONS INTO LOWERPART OF FIXTURE BELOW THE
BACKPLATE.
5. REASSEMBLE FIXTURE TO THE WALL MOUNTED REAR HOUSING. ENSURE THAT NO WIRES ARE
BEING PINCHED DURING REASSEMBLY.
ITEM 1
WARNING! INSTALLER IS RESPONSIBLE FOR ENSURING THE
RECOMMENDED CAULK
LAYOUT
www.hubbelloutdoor.com
ITEM 2
CAULK