Publicité
stone (not included), maintaining the angle of the
original cutting edge of the cutting blade.
6. Inspect the edge of the fixed blade and remove any burrs
with a fine tooth file.
7. Install sharpened cutting blade as described in the
Removing and Installing Blade section.
Blade Lubrication (Fig. A)
1. After use, remove the battery
2. Carefully apply a resin solvent to the exposed blades.
Storage (Fig. A)
1. After use, remove the battery and install blade cover.
2. Keeping your hands away from the blade, and store in a
dry location, away from the reach of children.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your CRAFTSMAN power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non‑metallic parts of the tool. These
chemicals may weaken the plastic materials used in
these parts. Use a cloth dampened only with water and
mild soap. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this product
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN‑recommended accessories should be used
with this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN. Call 1‑888‑331‑4569.
.
16
Versatrack™ (Fig. O)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
WARNING: To reduce the risk of serious personal
injury, do not use a damaged Versatrack™ hang hook
or Versatrack™ Trackwall. A damaged Versatrack™
hang hook or Versatrack™ Trackwall will not support
the weight of the tool.
WARNING: To reduce the risk of serious personal
injury, DO NOT suspend tool overhead or suspend
objects from the hang hook. ONLY suspend tool on the
Versatrack™ Trackwall using the hang hook.
WARNING: Ensure that the tool weight does not
exceed the maximum rated weight of 20 lb (9 kg) for
the selected Versatrack™ hook.
WARNING: When hanging objects on a Versatrack™
Trackwall rail, adequately space the tools in order to
not exceed 75 lb (35 kg) per linear foot.
iMPORTAnT: Versatrack™ accessories mount compatible
tools securely to the Versatrack™ Trackwall system.
1. Turn the tool off, remove the battery pack
and accessories.
CAUTION: Any product with exposed cutting teeth
must have them covered securely if it is to be on
the Versatrack™ Trackwall.
2. Flip or pull open the integral hang hook
when locked into position.
3. Mount the integral hang hook to the
Versatrack™ Trackwall.
nOTE: Versatrack™ accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1‑888‑331‑4569.
Repairs
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including
brush inspection and replacement, when applicable)
should be performed by a factory service center or
an authorized service center. Always use identical
replacement parts.
English
15
. It clicks
9
Publicité
