Leviton Slim Downlight Serie Mode D'emploi

WARNINGS:
• TO AVOID FIRE, SHOCK OR DEATH: TURN OFF POWER AT CIRCUIT BREAKER OR FUSE
AND TEST THAT THE POWER IS OFF BEFORE WIRING!
• TO AVOID SHOCK OR ELECTROCUTION, ground the fixture.
• To be installed by an electrician in accordance with all applicable electrical codes and regulations.
• Supply conductors (power wires) connecting the fixture must be rated at minimum of 90°C.
• Wear rubber soled shoes and work on a sturdy wooden or nonconductive ladder.
• To prevent damage to the wiring, do not expose wiring to edges of sheet metal or other
sharp objects.
• Installing contrary to instructions may cause unsafe conditions.
Installation
WARNING: TO AVOID FIRE, SHOCK OR DEATH: TURN OFF POWER
SUPPLYING THIS EQUIPMENT AND CONFIRM POWER IS OFF, before
installing, removing or servicing this equipment.
1.
Using the included template, mark and cut an opening in the ceiling.
2.
Remove junction box knock-outs for wiring and open the junction box.
NOTE: The junction box contains three wires: Hot (BLACK), Neutral
(WHITE), and Ground (GREEN).
Quick-connect Cable
to Luminaire
3.
Connect supply wires to junction box wires (GREEN to GREEN, BLACK to
BLACK, WHITE to WHITE).
4.
Connect downlight to junction box with the quick-connect cable. Select the
color temperature (CCT) using the 5CCT switch on the junction box. Then,
place the junction box into the ceiling.
5CCT switch
Commutateur 5 CCT
Interruptor 5CCT
Patents covering this product, if any, can be found on leviton.com/patents
LEVITON and the Leviton logo are trademarks of Leviton Manufacturing Co., Inc., and are registered trademarks in many countries throughout the world.
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada ULC to the attention of the Quality Assurance
Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1-800-405-5320.
LIMITED 5 YEAR WARRANTY
For Leviton's limited 5 year product warranty, go to www.leviton.com. For a printed copy of the warranty, call 1-800-824-3005.
Slim Downlight Series: Round Adjustable
INSTALLATION INSTRUCTIONS
Supply Wire
Câble d'alimentation
Cable de alimentación
Quick-connect Cable
Câble de raccordement rapide
Cable de conexión rápida
For Technical Assistance Call: 1-800-824-3005 (USA Only) or 1-800-405-5320 (Canada Only) www.leviton.com
Cat. Nos. DAR40 and DAR60
Ratings:120V AC, 60 Hz
CAUTIONS:
• Product must be mounted in locations and at heights and in a manner consistent with
its intended use, in compliance with NEC standards, and local codes and where it will
not readily be subject to tampering by unauthorized personnel. In Canada, product must
be mounted in compliance with CEC standards.
• This device is not intended for use with emergency exits.
• Do not exceed the input rating of the luminaire
• No user serviceable components. DO NOT attempt to service or repair.
• Connect to a 120V 60 Hz power source only; any other connection will void
the warranty.
5.
Push "Easy Mount" clips on the luminaire.
Easy Mount clip
Bride de
montage facile
Clip de montaje
fácil
6.
Insert downlight into the ceiling and release clips to secure the downlight
in the ceiling.
NOTE: Once installed, the downlight may be aimed by pressing up on the
inner bezel then tilting and rotating the light engine.
Mounting Plate Installation (Optional)
NOTE: The mounting plate can be used to provide extra support for a variety
of sizes (4 and 6 in.).
1.
Select the luminaire hole size by matching the luminaire to the rings on the
mounting plate.
2.
Select the ring that is slightly smaller than the outer diameter of the fixture.
3.
Using a pair of cutters, cut the ring out that corresponds to the luminaire
being installed
4.
Lay the mounting plate on the ceiling joist in the desired location and secure
to joists.
NOTE: Allow enough space for the junction box mounted on the mounting plate.
PK-A3518-10-02-6A
ENGLISH