Eldom acero CS30 Mode D'emploi page 10

OPERATING INSTRUCTION
EN
OPERATING INSTRUCTION
CORDLESS KETTLE CS30
CORDLESS KETTLE C275B/C275C
• GENERAL DESCRIPTION
• GENERAL DESCRIPTION
1. Spout + net filter
1. Spout
2. Opening lid
2. Opening lid
3. Handle
3. Lid release button
4. Water level indicator
4. On/off switch
5. On/off switch + control lamp
5. Handle
6. Rotating base
6. Control lamp
7. Rotating base
• INTENDED USE
Cordless kettle C275 is for boiling water. It is possible to boil 0.5 – 1.5 litre of water in the kettle.
• INTENDED USE
• OPERATION
Cordless kettle CS20 is for boiling water. It is possible to boil 0.5 – 1.7 litre of water in the kettle.
− The kettle base (6) must be put on a flat and dry surface.
− In the base there is some space for an excess cord. It is important for the cord to be led from
• OPERATION
the base (6) through a special groove so that the appliance could be stable.
− The kettle base (7) must be put on a flat and dry surface.
Before using the kettle for the first time fill it up (2-3 times) with water, boil the water
− In the base there is some space for an excess cord. It is important for the cord to be led from the base (7)
and then empty the kettle.
through a special groove so that the appliance could be stable.
− The kettle can be filled with water directly through the spout (1) or after opening the lid (2).
Before using the kettle for the first time fill it up (2-3 times) with water, boil the water and then empty
The kettle must not be filled up when on the base. Before switching on the kettle, make
the kettle.
sure that the lid (2) is properly fastened.
− The kettle can be filled with water directly through the spout (1) or after opening the lid (2).
−
− In order to open the lid (2) you must use the button (3). The minimum level of boiling water is 0.5 l. The maximum water level (1.5 l) is marked on the
indicator (4).
The kettle must not be filled up when on the base.
− The kettle starts working after putting the switch (5).
− The highest (max) and lowest (min) permissible water level is shown inside the kettle.
− The kettle working is signalled by the control lamp (5).
− The kettle starts working after putting the switch (4).
−
The kettle switches off automatically after the water has boiled.
− The kettle working is signalled by the control lamp (6).
−
You can stop heating water at any time by putting the switch (5) in the position '0'.
− The kettle switches off automatically after the water has boiled.
• FILTER
The filter does not remove the scale, but it prevents any deposits from getting inside the kettle while
• FILTER
the water is being poured in. The filter should be cleaned regularly. Hard water may block the filter
The filter does not remove the scale, but it prevents any deposits from getting inside the kettle while the water
after boiling water a couple of times.
is being poured in. The filter should be cleaned regularly. Hard water may block the filter after boiling water a
couple of times.
• CLEANING AND MAINTENANCE
−
Allow the unit to cool down completely before cleaning.
• CLEANING AND MAINTENANCE
−
Do not immerse the kettle in water while washing up.
− Allow the unit to cool down completely before cleaning.
−
The outside of the kettle may be wiped over with a damp cloth and washing-up liquid.
− Do not immerse the kettle in water while washing up.
−
Water stains inside the kettle can be removed by rubbing with a cloth moisten with white
− The outside of the kettle may be wiped over with a damp cloth and washing-up liquid,
vinegar; rinse the inside with water afterwards.
− Water stains inside the kettle can be removed by rubbing with a cloth moisten with white vinegar; rinse the
− Limescale should be removed in the following way:
inside with water afterwards.

− Limescale should be removed in the following way:

• Fill the kettle with 0.75 litre of water and bring it to boil.

• Switch the kettle off and disconnect the kettle from the power supply.

• Pour 0.1l of vinegar into a jug and leave the solution for a few hours.

• Discard the solution and rinse the inside with water.

• Fill the kettle with 1 litre of water and bring to boil.
• Discard the water and rinse the inside with water.
10
fill the kettle with 0.75 litre of water and bring it to boil,
switch the kettle off and disconnect the kettle from the power supply,
pour 0.1l of vinegar into a jug and leave the solution for a few hours,
discard the solution and rinse the inside with water,
fill the kettle with 1 litre of water and bring to boil,
discard the water and rinse the inside with water.
INSTRUCTION MANUAL
CORDLESS KETTLE CS20
• TECHNICAL DATA
• TECHNICAL DATA
− power: 2520-3000W
− power: 1300-1540W
−
mains voltage:
− mains voltage: 220-240V ~ 50-60Hz
220-240V ~ 50-06Hz
− 1.7 litre capacity
2.0
−
1.5 litre capacity
2.0