Publicité
Les langues disponibles
Les langues disponibles
1U03 1881
Model: ECP-360
SAFETY INSTRUCTIONS
Before installation and operation, read these instructions carefully
and use this product only in the manner described by the
manufacturer in the operation manual.
The instruction shown below are used to alert you to potential
personal injury and property damage hazards.
There are three hazard classifications based on potentially
dangerous situations.
Obey all safety instructions that show these symbols to avoid
possible injury, death and property damage.
WARNING:
WARNING indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION:
CAUTION indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
CAUTION:
CAUTION used without the safety
alert symbol indicates a potentially
hazardous situation which, if not
avoided, may result in property
damage.
NOTE: The safety instructions are explained with the following
pictographic symbols.
means prohibition. It indicates actions, if any, that
mustn't be done.
means forcible execution. It indicates actions, if
any, that must be done.
WARNING
1. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b) Before servicing or cleaning the unit, switch power
off at service panel and lock the service
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag,
to the service panel.
2. To reduce the risk of fire or electric shock, do not
use this product with any solid-state speed control
device.
3. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Installation work and electrical wiring must be
done by a qualified person(s) in accordance with
all applicable codes and standards, including fire-
rated construction.
1. Preparation
WARNING:
• Ensure that the metal duct does not touch other metal housing materials,
otherwise fire or electric shock could result.
Roof cap
1
This range hood is designed to
7" round duct
install using anchor bolts as
(For vertical discharge)
illustrated and discharge upward.
For vertical discharge, run duct
work between the hood location
and roof cap location.
To get the best result, use a
minimum number of transitions
and elbows. Be sure to attach a
roof cap to avoid rain from
entering into the exhaust duct.
Range hood
CAUTION:
• Install the range hood unit using anchor bolts durable
enough to support its weight (withstand load: more than
441lbs. (200kg)/pc). Otherwise, it may be detached and
fall down.
2
Referring to the figure below, make an opening on the ceiling and
reinforce around the opening with some beams. Then, make 5 holes
as shown in the figure.
3-9/16"
3-9/16"
(90)
(90)
∅
1-3/16"
∅30)
(
4-∅9/16"(∅14)
11"(280)
Front
14-3/16"(360)
Unit: inch (mm)
3
Arrange the ends of 7" round duct and conduit so that they can connect
with the top of the range hood unit.
4
Pass 4 threaded rods*
(not supplied) through
the holes of the
ceiling and put
washers, spring
washers, and nuts on
the rods, then fix
them to the beam.
(*∅12~14 anchor
bolt, length = duct
height - 40mm)
Threaded rod
Conduit
Duct
Duct
5
(1) Pull out the inner frame after removing 4 screws fastening to the
outer frame.
Note: Keep the screws for reusing later.
(2) Fix the inner frame to the ceiling using
8 wood screws supplied after aligning
its holes with the threaded rods.
6
Secure the threaded rods by adding
washers, spring washers, and nuts
from the ends of the rods.
7
Set 4 flange-nut (not supplied) on the
threaded rods as shown for fixing the
supplied hanging brackets later.
6
*Not Supplied
Beam
Ceiling
Inner Frame
Washer*
Spring-Washer*
Nut*
7
Flange Nut
50mm
INSTALLATION MANUAL
b) Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney)
of fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer's
guidelines and safety standards such as those
published by the National Fire Protection
Association (NFPA), and The American Society
for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code
authorities.
c) When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
d) Ducted fan must always be vented to outdoors.
4. TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.
5. This unit must be grounded.
6. Check that the hood is correctly installed, since
incorrect installation could result in the range hood
becoming detached and falling off.
7. Connect only to an AC120 Volt power source or
the range hood could result in fire, electric shock,
and damage.
CAUTION
1. For general ventilating use only. Do not use to
exhaust hazardous or explosive material and
vapors.
2. To reduce the risk of fire and to properly exhaust
air, be sure to duct air outside. Do not vent exhaust
air into spaces within walls, ceilings or into attics,
crawl spaces or garages.
3. Read specification label on this product for further
information and requirements.
4. Use only for the purpose of kitchen ventilation.
5. Do not install this range hood in the bathroom or
in other wet rooms since electrical shock and
damage may result.
6. Fasten the filter and other parts securely. Incorrect
attachment may result in personal injury or
property damage.
2. Range Hood Mounting
CAUTION:
• Wear working gloves to avoid injury.
1
Detach the tape on the exhaust
port, then with paying attention to
the shutter opening direction, fix it
using screws attached on the top
plate.
2
Detach the rectifier baffle
panel by loosening 2 fixing
screws, sliding it to dislocate
the keyholes from the
screws, and disengage it
from the catches.
3
Detach the filters by
turning the fixing
knobs counter-
crockwise, and
disengaging them
2
from the supporting
Rectifier
baffle panel
groove.
Stringpiece
4
Beam
Attach the outer frame to the range hood unit using 4 screws supplied.
5
Attach 4 hanging brackets supplied to the range hood unit and fix them
as shown. As the fixing screws are attached on the top plate, remove
them once and use for fastening the hanging brackets.
Ceiling
4
5
Outer frame
Hanging bracket
Stringpiece
Beam
Ceiling
Inner Frame
Nut
Spring-
Washer
Washer
(Not Supplied)
6
With inserting the inner
frame into the outer
Duct
frame and the exhaust
port into the duct, lift up
40mm
the range hood unit and
pass the threaded rods
through the hanging
brackets as shown.
_
7
Fix the range hood unit
5
(1)
by adding 4 flange nuts
Exhaust port
(not supplied) to the
Inner frame
threaded rods as shown.
Outer frame
Note: Check that the range hood unit is fixed at the specified height
horizontally and adjust if not.
Screw
8
Fasten the outer frame
and inner frame using
4 screws removed
before as shown.
9
_
Make the duct joint
5
(2)
secure and air-tight
using non-flammable
tape such as duct tape,
etc (not supplied).
Non-flammable tape
Range Hood
NAMES OF PARTS
Inner Duct
Inner Frame
Inner Duct
Outer Frame
Hanging
Bracket
Outer Duct
Control Switches
Filter
Fan
Rectifier Baffle Panel
Pilot Lamp
OFF Switch
Low Switch
DIMENSIONS
Unit: inch (mm)
14-3/16"(360)
1" (26)
7" (177.5)
18"(457)
11-13/16"(300)
16-5/8"(422)
6-15/16"( 176)
36"(913)
INSTALLATION
3. Connecting Power Supply Wires
WARNING:
• Electrical wiring should be done by a qualified person(s) in accordance
with all applicable codes and standards, including fire-rated construction.
An unqualified person doing the work could result in fire, electric shock
or injury.
Tape
• This range hood uses 120V AC. Do not connect to other voltage since
fire, electric shock or damage could result.
Shutter
1
Remove the nut from the conduit
opening direction
connector at the end of power
wiring.
Exhaust port
WARNING:
Loosen 2 screws
Be sure to switch OFF the power
to remove the filter
at service panel before wiring.
3
Filter
2
Remove two screws fixing the wire cover and detach it.
Loosen 2 screws to remove
the rectifier baffle panel
Wire cover
Screw
3
Connect the conduit through the connecting hole of the body using the
nut previously removed.
Conduit
Inner frame
Outer frame
4
Connect wires tightly and
securely using wire
Flange nut
connectors (not supplied).
6
Connect the electrical wires
as follows:
7
• Black to Black
• White to White
• Green to Green
5
Replace the wire cover with the
screws removed previously.
Make sure that all wires are
connected properly and
Screw
enclosed inside of the wiring
compartment.
8
9
CIRCUIT DIAGRAM
Outer Duct
White
120V
Black
60Hz
Green
Purple
Lamp Switch
High Switch
Medium Switch
23-5/8"(600)
RANGE HOOD LOCATION
1
The range hood must be installed
13"(330)
just above the cooktop.
2
The minimum distance from the
cooking surface to the bottom of the
range hood must be 24".
3
The total weight of the ECP-360
range hood unit is 86.0 lbs. (39 kg)
4
Power requirements are:
AC120 V, 60 Hz, 3.0 Amp
CAUTION:
• Check that the hood is correctly installed, since incorrect installation could
result in the detachment of the range hood and the unit could fall down.
• To protect hands from injury, wear working gloves when installing the
range hood.
24"(610)
1
Attach the inner duct (front and rear).
Insert the upper edge of the inner duct into the gap between the inner
frame and ceiling with sliding on the guide frame on both sides, then
push the front and rear ducts until they are fixed by their roller catch.
Note: Be careful not to attach the duct upside down.
2
Attach the outer duct (front and rear).
Place the outer duct on the range hood unit, and push the front and
rear ducts until they are fixed by their roller catch.
Conduit
Note: Be careful not to attach the duct upside down.
(Not supplied)
3
Fix the outer duct (front and rear) to the range hood unit using 4 screws
supplied as shown.
Ceiling
Nut
(Not supplied)
Inner frame
Inner duct
1
Inner duct
2
Outer duct
Screw
Assembly
1
Attach the filters and rectifier baffle panel referring to the steps
described in "2. Range Hood Mounting".
Nut
2
Two 50 W halogen light bulbs (not supplied)
can be mounted in this range hood.
Prior to function check, install light bulbs
(PAR20 bulb, in the base diameter 26 mm:
medium base), rated 120 V - 50 W or below.
Turn the lamps clockwise
to install them.
Check
1
Turn on the power to the range hood.
2
Make sure that the switches and light operate correctly.
Refer to page 4 of the Operation Manual.
3
Make sure that the range hood functions properly and it has no
abnormal noises and/or vibration.
Wire connector
6. Explanation to the End User
(1) Referring to the Operation Manual, explain the operation of this range
hood to the end user.
(2) The Installation Manual and Operation Manual should be given to the
Screw
end user.
Wire cover
Lamp Switch
Fan Switch
Connector
Pilot Lamp
Connector
Black
White
Grey
Yellow
Black
Lamp 50W
Motor
Yellow
Yellow
White
White
Black
Black
Connector
Connector
Connector
White
White
Black
Black
Connector
Lamp 50W
Grey
Grey
Purple
Capacitor
ACCESSORIES
• Screw M5.1×45
• Exhaust Port
Eight (8) pcs.
One (1) pc.
• Hanging Bracket
• Screw M5×10
Four (4) pcs.
Four (4) pcs.
24"(minimum)
Cook top
4. Attaching Duct Cover
Inner duct
Hook
2
Inner frame
1
Slit
Hook
3
Roller catch
5. Assembly and Check
Filter
Rectifier baffle panel
Bulb
(Not supplied)
Push to turn ON
Publicité
