Ultranatura BR-100 Mode D'emploi D'origine page 22

Anleitung_BR_100_SPK7__ 28.02.14 10:48 Seite 22
GB
6. Before starting the equipment
6.1 Assembling the components
Some parts of the mower come disassembled. For
quick and easy assembly, read and follow the
instructions below.
Notice: You will need the following additional tools
(not supplied) for assembly, and also for maintenance
work:
A flat oil drip tray (for changing the oil)
n
A 1 liter measuring jug (oil/petrol resistant)
n
A petrol can
n
A funnel (suitable for the tank's petrol filler neck)
n
Household wipes (to wipe up oil/petrol residue;
n
dispose of these at a filling station)
A petrol suction pump (plastic, available from DIY
n
stores)
An oil can with hand pump (available from DIY
n
stores)
Engine oil
n
Assembly
1. Assemble the push bar (Item 3) as shown in Fig.
3a, 3b and 3c. For fastening choose one of the
holes to suit the required height of the push bar.
Important. The identical height must be set on
both sides. Ensure that the cords which are
fastened later are not in the way.
2. Insert the grip of the starter cord (Fig. 3c/Item 9)
into the hook provided for that purpose as shown
in Figure 3c.
3. Fasten the cords to the push bar with the supplied
cable clip (Fig. 3d/Item 10).
4. Lift the ejector flap (Fig. 4 / Item 5a) with one
hand and hook in the grass bag (Fig. 4/Item 4) as
shown in Figure 4.
6.2 Setting the cutting height
Warning! Adjust the cutting height only when the
engine is switched off and the plug boot has
been pulled.
Before you begin to mow, check to ensure that
n
the blade is not blunt and that none of the fasten-
ers are damaged. To prevent any imbalance,
replace blunt and/or damaged blades as a set
only (if applicable). To carry out this check, first
switch off the engine and pull the spark plug boot.
The cutting height is centrally adjusted with the
n
cutting height adjustor lever
(Fig. 6-7/Item 8). Different cutting heights can be
selected.
Pull the adjustor lever out and select the desired
n
cutting height. The lever snaps into the desired
position.
22
7. Using the petrol lawn mower
Notice:
The engine is supplied without oil and petrol.
Therefore, be sure to add oil and petrol before
starting the engine.
In order to avoid any unintentional start-ups of the
lawn mower, it comes equipped with an engine brake
(Fig. 5a/Item 1a) which must be pulled back before
the engine can be started. When the engine start/stop
lever is released it must return to its initial position, at
which point the engine automatically switches off.
Before you start mowing, you should run through this
process several times in order to ensure that the
machine is working properly. Whenever you need to
perform any kind of adjustment and/or repair work on
your lawn mower, wait until the blade has come to a
complete stop. Always switch off the engine before
carrying out any adjustments, maintenance or repairs.
Note:
1. Engine brake (Fig. 5a/Item 1a): Use the engine
start/stop lever to switch off the engine. When you
release the engine start/stop lever, the engine
and blade will automatically stop. To mow, hold
the lever in the working position (Fig. 5b). Before
you start to mow, check the start/stop lever
several times to be sure that it is working properly.
Ensure that the tension cable can be smoothly
operated (i.e. is not catching or kinking in any
way).
2. Drive lever/clutch lever (Fig. 5a/Item 1b): If you
press this (Fig. 5c) the clutch for the drive will be
closed and the lawnmower will start to move with
the engine running. Release the drive lever in
good time to stop the moving lawnmower.
Practice starting and stopping before you use the
mower for the first time until you are familiar with
controlling the mower.
3. Warning: The blade begins to rotate as soon as
the engine is started.
Important: Before you start the engine, move the
engine brake several times to be sure that the
stop cable is properly working.
Note: The engine is factory set to a speed that is
optimal for cutting and blowing grass into the
basket and is designed to provide many years of
use.
4. Check the oil level.
5. Use a funnel and measuring vessel to fill the tank
with petrol. Make sure that the petrol is clean.
Warning: Never use more than one safety petrol can.