Télécharger Imprimer la page

EINHELL TE-SW 18/610 Li Mode D'emploi page 12

Publicité

Les langues disponibles

Les langues disponibles

18V 4.0Ah/6.0Ah PXC Plus Lithium-Ion battery
18V 5.0Ah/8.0Ah PXC Plus Lithium-Ion battery
18V PXC Dual Port Fast Charger
18V PXC Fast Charger
Contact your local retailer for more specifi c
models of batteries and charger available in your
area. You can also explore battery + charger
options at Einhell.com.
3. Intended use
The cordless push sweeper is suitable for
sweeping level and dry surfaces.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.
4. Technical data
Motor power supply: ............................ 18V
Volume of debris collector: ................. 5.3 Gallons
Working width: ................................................ 24"
Weight (tool only): ...................................22.7 lbs
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
Reduce noise generation and vibration to a
minimum!
Use only equipment that is in perfect
condition.
Maintain and clean the equipment regularly.
Adapt your way of working to the equipment.
Do not overload the equipment.
Have the equipment checked if necessary.
Switch off the equipment when not in use.
Wear gloves.
Anl_TE_SW_18_610_Li_NA_SPK7.indb 12
Anl_TE_SW_18_610_Li_NA_SPK7.indb 12
EN
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is applied.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be
considered (for example, times in which the
electric tools are switched off and times in which
the tool is switched on but operates without load).
5. Before starting the equipment
5.1 Fitting the feed-in brushes (Fig. 3-5)
Fit the feed-in brushes (4,5) as shown in Figs. 3-5.
Make sure that you fi t them in accordance with
the markings on the brushes and brush mounts.
5.2 Fitting the push bars (Fig. 6-9)
Fit the top push bar and bottom push bar (2, 3)
as shown in Figs. 6-8. Make sure that the pins are
properly latched in position on both sides (Fig. 6,
Item 3.1) during assembly. The height of the top
push bar can be adjusted a little by selecting the
fastening hole (Fig. 7, Item 2.1, 2.2) accordingly.
Secure the top and bottom push bars using 4
fastening screws (12), washers (13) and quick
release levers (11). Then fasten the power cable
to the push bars (Fig. 9) with the cable holders
(10).
Fitting the battery (Fig. 10)
Open the battery cover (15). To do so, fl ip the
cover up as shown in Fig. 10. Then slot the
rechargeable battery (17) into the mount and
push it forward until you hear the battery engage.
- 12 -
25.04.2024 09:15:38
25.04.2024 09:15:38

Publicité

loading

Ce manuel est également adapté pour:

2352045