Important Safety Instructions; General Specifications; Functional Description - Milwaukee 2216-20 Manuel De L'utilisateur

IMPORTANT SAFETY INSTRUCTIONS

WARNING
READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS.
Failure to follow the warnings and instructions may result in electric shock, fi re and/or serious
injury, as well as instrument damage and/or damage to the equipment being tested.
Save these instructions - This operator's manual contains important safety and operating
instructions for the MILWAUKEE Digital Multimeter. Before using, read this operator's
manual and all labels on the Digital Multimeter.
DANGER
Never make measurement on a circuit in which voltage over 600 volts AC/DC rms exists. Use
only leads rated CAT III 600V or better.
Do not apply more than the rated voltage, as marked on the Digital Multimeter, between ter-
minals or between any terminal and earth ground.
Do not attempt a current measurement when the open voltage is above the fuse protection
rating. Suspected open circuit voltage can be checked with voltage function.
Do not attempt to make measurement in the presence of fl ammable gases. Otherwise, the use
of the instrument may cause sparking, which can lead to an explosion.
Never attempt to use the instrument if its surface or your hand is wet.
Do not exceed the maximum allowable input of any measuring range.
Only test on unenergized circuits unless absolutely necessary.
Check meter functionality on a known circuit fi rst. Never assume meter is working. Assume
circuits are live until they can be proven de-energized.
Never open the battery cover during a measurement.
Do not ground yourself while measuring. Avoid body contact with earthed or grounded sur-
faces such as pipes, radiators, ranges and refrigerators.
This instrument is to be used only in its intended applications or conditions. Otherwise, the
instrument's safety functions may not work, resulting in serious personal injury and instru-
ment damage.
To reduce the risk of injury from shock and arc blasts, always wear personal protective
equipment where live conductors are exposed.
WARNING
Never attempt to make measurement if any abnormal conditions, such as broken case and
exposed metal parts are found on the instrument.
Comply with local and national safety requirements when working in hazardous locations.
Keep fi ngers behind the guards and away from test lead tips during measurements.
Do not rotate the rotary dial while the test leads are being connected.
Never attempt a voltage measurement with the test lead inserted into the A input terminal.
Verify proper operation on a known source before use or taking action as a result of the in-
dication of the instrument.
Do not install substitute parts, replace fuse or make any modifi cation to the instrument. For
repair or re-calibration, return the tool to a factory Service/Sales Support Branch or authorized
service station.
Do not try to replace the batteries if the surface of the instrument is wet.
Disconnect all the cords and cables from the object under test and power off the instrument
before opening the battery cover for battery replacement.
This tool is designed to be powered by 2-AA batteries properly inserted into the MILWAUKEE
Digital Multimeter. Do not attempt to use with any other voltage or power supply.
2
WARNING
Install battery according to polarity (+ and –) diagrams.
Do not leave batteries within the reach of children.
Do not mix new and used batteries. Do not mix brands (or types within brands) of batteries.
Properly dispose of used batteries.
Do not incinerate or dismantle batteries.
Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact
accidentally occurs, fl ush with water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.
CAUTION
Set the rotary dial to an appropriate position before starting measurement.
Disconnect test leads from test points before changing rotary dial functions.
Never connect to a source of voltage with the dial function in OFF/Ω/ / / /
Firmly insert the test leads.
Do not expose the instrument to the direct sun, high temperature and humidity or dew fall.
Altitude 2000m or less. Appropriate operating temperature is within 14°F and 122°F (-10ºC
and 50ºC).
Keep away from excess dust and water.
Be sure to power off the instrument after use. When the instrument will not be in use for a long
period, place it in storage after removing the batteries.
Use a damp cloth or neutral detergent for cleaning the instrument. Do not use abrasives or
solvents.

GENERAL SPECIFICATIONS

Accuracy is specifi ed for 1 year after calibration, at
operating temperatures of 14°F to 122°F (-10°C to
50°C), with relative humidity less than 85%.
Maximum voltage between any terminal and
earth ground.... 600 V
Temperature ....
Operating: 14°F to 122°F (-10°C to 50°C)
for Current measurements: 14°F to 104°F
(-10°C to 40°C)
Storage: -40°F to 140°F (-40°C to 60°C)
Operating Altitude.... 2,000 meters
IP Rating
(Ingress Dust & Water Protection) .... IP64
Drop Test .... 1 Meter
Battery .... 2 AA, NEDA 15A, IEC LR6
Battery Life .... Approx. 26 hours with all lights on,
240 hours without backlight.
Fuse .... 600V AC/DC, 10A fast-acting
(Milwaukee p/n 22-89-0300)
Safety Compliances .... EN61010-1,
UL 61010-1, UL 61010-031 (Probes),
EN61010-031 (Probes),
IEC/EN 61010-1 2nd Edition for measurement
Category III, 600 V, Pollution Degree 2,
EMC EN61326-1
Certifi cations .... cULus, CE, C1
.

FUNCTIONAL DESCRIPTION

1
2
3
9
8
7
4
6
5
1. Display 7. Rotary dial
2. Range button 8. Min/Max button
3. Backlight button 9. Hold button
4. VΩ Terminal input 10. Accessory bay
(on back, not shown)
5. COM Terminal input
6. A (Amps) Terminal input
3