Publicité
Les langues disponibles
Les langues disponibles
FILLING OIL TANK:
WARNING: Removing the battery pack before
filling the oil tank.
1. Set chainsaw on any suitable surface with oil filler
cap facing upward.
2. Clean area around the oil filler cap with cloth and
unscrew the cap by turning it counter clockwise.
3. Add bar and chain oil until tank is full.
4. Avoid dirt or debris entering oil tank, refit oil filler
cap and tighten by turning clockwise until hand
tight.
IMPORTANT: To allow venting of the oil tank,
small breather channels are provided between
the oil filler cap and the strainer, to prevent leakage,
and ensure machine is left in a horizontal position
when not in use.
It is important to use bar and chain lubricant (not
provided) that is formulated to perform over a wide
temperature range with no dilution required.This
can be found at the location where you purchased
this saw or your local hardware store. Do not use
dirty, used or otherwise contaminated oils. Damage
may occur to the bar or chain. Use of non approved
oil will void the warranty.
Do not swallow. If swallowed, call a physician
immediately. Keep out of reach of children. Store
away from heat or open flame.
CHECKING THE AUTOMATIC OILER
Proper functioning of the automatic oiler can be
checked by running the chainsaw and pointing the tip
of the guide chain bar towards a piece of cardboard
or paper on the ground. If an increasing oil pattern
develops on the cardboard, the automatic oiler is
operating fine. If there is no oil pattern, despite a full
oil reservoir, contact WorxNitro customer service
agent or WorxNitro approved service agent.
CAUTION: Do not touch the ground with the
chain. Ensure safety clearance of 16".
5. OPERATION
1. BEFORE USING YOUR CORDLESS TOOL
WARNING! The charger and battery pack are
specially designed to work together so do not
attempt to use any other devices. Never insert or
allow metallic objects into your charger or battery
pack connections because of an electrical failure and
hazard will occur.
NOTE: Your battery pack is shipped UNCHARGED
and you must charge once before use.
The battery charger supplied is matched to the Li-ion
battery installed in the machine. Do not use another
battery charger.
2. CHECKING THE BATTERY CHARGE-LEVEL (See
Fig. G)
20V 12" Brushless Chainsaw
The battery level can be known from the battery
indicator light by pressing the button beside the
lights.
Note: Fig. G only applies for the battery pack with
battery indicator light.
3. CHARGING YOUR BATTERY PACK (See Fig. H)
The Li-ion battery is protected against deep
discharging. When the battery is empty, the machine
is switched off by means of a protective circuit. The
battery must be fully charged before the first use.
In a warm environment or after heavy use, the battery
pack may become too hot to permit charging. Allow
time for the battery to cool down before recharging.
Note: Always fully charge the battery. More details
can be found in charger's manual.
4. TO REMOVE OR INSTALL BATTERY PACK (See
Fig. I)
Depress the battery pack release button to remove
the battery pack from your tool. After recharging,
insert the battery pack into the battery port. A simple
push and slight pressure will be sufficient until a click
is heard. Check to see if the battery is fully secured.
Note: When removing the battery pack, hold it firmly
to avoid dropping and injury.
5. SWITCHING ON AND OFF (SEE FIG. J)
ATTENTION: Check the battery packs before
using your cordless tool. Only use the battery
pack listed in the accessories section.
For switching on the tool, press the lock-out button,
then fully press the on/off trigger and hold in this
position. The lock-out button can now be released.
For switching off, release the on/off trigger.
NOTE: The chain brake must be activated in order for
the saw to be switched on.
6. CHAIN BRAKE (SEE FIG. K)
The chain brake is a safety mechanism activated
through the front hand guard, when kickback occurs.
Chain stops immediately.
The following function check should be carried out
at regular intervals. Pull the front hand guard towards
the operator (position
To activate the chain brake, push front hand guard
forwards (position
).
NOTE: If the saw is unable to start, even though it is
assembled properly and working with a fully charged
battery pack, then you should check if the chain brake
is in the correct position (position
7. CUTTING
Important: Is the oil tank filled? Check the oil
level window prior to starting and regularly
during operation (See Fig. L). Refill oil when oil level
is low. A full oil tank will last approx. 12 minutes of
cutting depending on sawing intensity and stops.
Check recent replaced chain tension about every 10
) to deactivate chain brake.
).
EN
15
Publicité
