Publicité
Les langues disponibles
Les langues disponibles
NOTE: The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared noise emission value(s) may
also be used in a preliminary assessment of exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-2-4:
Work mode: Sanding
Vibration emission (a
) : 2.5 m/s
h
Uncertainty (K) : 1.5 m/s
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-1:
Work mode: Cutting with plunge cut saw blade
Vibration emission (a
) : 2.5 m/s
h
Uncertainty (K) : 1.5 m/s
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-1:
Work mode: Cutting with segmental saw blade
Vibration emission (a
) : 2.5 m/s
h
Uncertainty (K) : 1.5 m/s
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-1:
Work mode: Scraping
Vibration emission (a
) : 2.5 m/s
h
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
2
or less
2
2
or less
2
2
or less
2
2
or less
2
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING:
Read all safety warnings, instruc-
tions, illustrations and specifications provided
with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Cordless multi tool safety warnings
1.
This power tool is intended to function for
sawing, cutting, scraping and sanding. Read
all safety warnings, instructions, illustrations
and specifications provided with this power
tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious
injury.
2.
Hold power tool by insulated gripping sur-
faces, when performing an operation where
the cutting accessory may contact hidden wir-
ing. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
3.
Use clamps or another practical way to secure
and support the workpiece to a stable plat-
form. Holding the work by hand or against your
body leaves it unstable and may lead to loss of
control.
4.
Always use safety glasses or goggles.
Ordinary eye or sun glasses are NOT safety
glasses.
5.
Hold the tool firmly.
Make sure the application tool is not contact-
6.
ing the workpiece before the switch is turned
on.
Keep hands away from moving parts.
7.
8.
Do not leave the tool running. Operate the tool
only when hand-held.
9.
Always switch off and wait for the blade to
come to a complete stop before removing the
blade from the workpiece.
10. Do not touch the application tool or the work-
piece immediately after operation; they may be
extremely hot and could burn your skin.
11.
Do not operate the tool at no-load
unnecessarily.
5 ENGLISH
Publicité
