Kichler Talman 59146BKT Guide Rapide

FIXTURE DIAGRAM
H
I
E
J
G
PARTS LIST
[A] Strap Mounting Screw (2)
[B] Outlet Box (not supplied)
[C] Mounting Strap
[D] Mounting Screw (2)
CAUTIONS
CAUTION – RISK OF SHOCK:
Disconnect Power at the main circuit breaker panel or main fusebox before starting and during
the installation.
WARNING:
1. This fixture is intended for installation in accordance with the National Electrical Code (NEC)
and all local code specifications. If you are not familiar with code requirements, installation by a
certified electrician is recommended. Failure to adhere to these codes and instructions may result
in serious injury and/or property damage and will void the warranty.
INSTRUCTIONS FOR MOUNTING FIXTURE OUTDOORS
AND/OR IN WET LOCATIONS:
1) Mounting surface should be clean, dry, flat and 1/4" larger than the canopy on all sides. Any gaps
between the mounting surface and canopy exceeding 3/16" should be corrected as required.
2) With silicone caulking compound, caulk completely around where back of canopy meets the wall
surface to prevent water from seeping into outlet box.
CLEANING:
• Always be certain that electric current is turned off before cleaning.
• Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.
REV 7-MAR-2023
A
F
[E] Socket
[F] Canopy
[G] Socket Ring
[H] Knob (2)
© 2023 Kichler Lighting LLC. All rights reserved.
For warranty information please visit: kichler.com/warranty
C
D
B
[I] Socket Base Cup
[J] Glass Shade
We're here to help
INSTALLATION INSTRUCTIONS
1. Find the appropriate threaded holes on mounting strap[C] that align with
hole distance in canopy[F]. Thread mounting screws[D] into threaded
holes starting from outlet box[B] side.
2. Attach mounting strap[C] to outlet box[B] using the strap mounting
screws[A]. Mounting strap can be adjusted to suit position of fixture.
3. Grounding instructions: (See Illus. a or b).
a. On fixtures where mounting strap is provided with a hole and two
raised dimples, wrap ground wire from outlet box around green
ground screw, and thread into hole.
b. On fixtures where a cupped washer is provided, attach ground wire
from outlet box under cupped washer and green ground screw, and
thread into mounting strap.
If fixture is provided with ground wire, connect fixture ground wire to
outlet box ground wire with wire connector after following the above
steps. Never connect ground wire to black or white power supply wires.
a
WIRE CONNECTOR
OUTLET BOX
GROUND
FIXTURE
GROUND
OUTLET BOX
DIMPLES
GROUND
GREEN GROUND
SCREW
4. Make wire connections. Reference chart below for correct connections
and wire accordingly.
Connect Black or Red
Supply Wire to:
Black
*Parallel cord (round &
smooth)
Clear, Brown, Gold or Black
without Tracer
Insulated wire (other
than green) with copper
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
5. NOTE: Fixture should be installed with socket[E] facing DOWN as
shown.
Push fixture to wall, carefully aligning the mounting screws protruding
from the mounting strap with holes in canopy.
NOTE: Make sure all wires are inside canopy and do not get pinched
between mounting strap and canopy or wall and canopy of fixture.
6. Screw knobs[H] onto threads protruding through holes in canopy (2
places) and tighten to secure fixture to wall.
7. Carefully slip small hole in glass shade[J] over socket[E]. Make sure glass
shade is fully seated against socket base cup[I], and secure in place by
threading socket ring[G] onto socket until snug against inside surface of
glass shade. DO NOT OVER-TIGHTEN.
8. Insert recommended bulb(s) (not included).
866-558-5706
Hrs: M-F 9am to 5pm EST
b
FIXTURE
GROUND
GREEN GROUND CUPPED
WASHER
SCREW
Connect White Supply
Wire to:
White
*Parallel cord (square &
ridged)
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with silver
conductor
Neutral Wire
IS-59146-US