Publicité
IMPORTANT
Please read these instructions carefully before you start to assemble this product .
Please carry out the steps in the order set out in these instructions.
Keep these instructions in a safe place for future reference.
Safety advice
For safety purposes we strongly recommend the product to be assembled by at least two people.
Some parts may have sharp edges. Please be careful when handling components. Always wear
gloves, eye protection, and long sleeves when assembling or performing any maintenance on
your product.
Do not attempt to assemble the product in windy or wet conditions.
Do not attempt to assemble the product if you are tired, have taken drugs,
medications or alcohol, or if you are prone to dizzy spells.
Dispose of all plastic bags safely - keep them away from children's reach.
Keep children away from the assembly area.
When using a stepladder or power tools, make sure that you are following
the manufacturer's safety advice.
Do not climb or stand on the roof.
Do not hang or lay on the profiles.
Heavy articles should not be leaned against the poles.
Keep roof and gutters clear of snow, dirt & leaves.
Heavy snow load on the roof can make it unsafe to stand below or nearby.
If color was scratched during assembly it can be fixed.
Cleaning instructions
In order to clean the product, use a mild detergent solution and rinse with
cold clean water.
Do not use acetone, abrasive cleaners, or other special detergents to clean the panels.
Clean the product once assembly is complete.
Before starting assembly
Choose your site carefully before beginning assembly.
The ground surface must be perfectly flat and leveled and have a solid base such as concrete,
asphalt, deck etc.
Sort the parts and check against the content parts list.
Parts should be laid out close at hand. Keep all small parts (screws etc.) in a bowl so they do
not get lost.
Please consult your local authorities if any permits are required prior to constructing the product.
During Assembly
When encountering the information icon, please refer to the relevant
assembly step for additional comments and assistance.
an.
Attention
During assembly use a soft surface below the parts to avoid scratches and
damages.
Please make sure you install the panels with the UV protected side
out (marked with "THIS SIDE OUT") and remove the sticker as panels are in place.
The Vitoria carport has 4 gutters heads, you can choose whether to make them active
or keep them in its original condition - non active. To activate please follow Step 15
Step 1: Carefully spread silicone glue along the cross-section of the profile #7573
and at once attach the profiles together. It is recommended to wipe the extra residue silicone.
Step 3:
It is recommended to place a sheet/Carton below the parts to avoid scratches and peeling of paint.
Profile should be fixed in front of the second set of holes from the edge.
Step 5: Please connect two parts when one person lifts the construction at an angle as
illustrated in drawing 5a.
Step 9: Central channel should remain open. Please place the panel aside the central channel
of the arched profile, as illustrated in the top circle. Please note you install the panels with
the UV protected side out (marked with "THIS SIDE OUT") and peel the film strip covering the
panels.
Step 10: Do not tighten the screws fully, until both sides panels in place.
Step 11: Profile stretching occurs only when all screws closed fully, at the same time; on both sides.
Step 12: Repeat and follow the same action for all profiles left as explained in stages 10-11.
Step 15: Optional - if you wish to use the gutters heads for water drainage, pop the inner
plastic cap with a screwdriver and then remove it with your finger.
Step 17: Level the profiles legs and then adapt screws and plugs to the ground type.
Tighten all screws at the end of assembly.
Do not tighten screws and nuts (8192 & 466) until completion of assembly process.
These 2 icons indicate if screws'tightening is required or not.
A
>-C1411
4*
466
Note:
Anchoring this product to the ground is essential to its stability and rigidity.
It is required to complete this stage in order for your warranty to be valid.
Publicité
