Publicité
Les langues disponibles
Les langues disponibles
PRODUCT IDENTIFICATION
Rear
Handle
Rear Hand
Guard
Power Cord
Oil Level Sight Hole (located on
saw body, hidden by front handle)
Front
Handle
Motor
Housing
Figure 2 - Electric Chain Saw
CHAIN SAW NAMES AND TERMS
Bucking Process of cutting a felled tree or log into lengths.
Felling Process of cutting down a tree.
Felling Cut Final cut when felling a tree. Make this cut on
opposite side of tree from notching cut.
Front Hand Guard Shield between front handle and guide
bar. Protects left hand while using saw. When kickback occurs,
the front hand guard is moved forward by the back of
operator's left hand. This stops the saw chain quickly, reducing
the chance of serious injury.
Front Handle Located at front of saw body.
Guide Bar Metal bar that extends from saw body. The guide
bar supports and guides chain.
Guide Bar Nose Tip or end of guide bar.
Kickback Quick backward and upward motion of guide bar.
Kickback may occur when tip of guide bar touches an object
while chain is moving. The guide bar will kick up and back
towards operator.
100549
Limbing Process of cutting limb(s) from a felled tree.
Low-Kickback Chain Chain that reduces chance of
Front Hand Guard/
kickback as required by CSA Standard Z62.3.
Chain Brake
Normal Cutting Position Stance used while making
Saw
bucking and felling cuts.
Chain
Notching Cut Notch cut in tree that directs fall of tree.
Oiler Control System for oiling guide bar and chain.
Power Head Chain saw without chain and guide bar. Also
known as saw body.
Guide Bar
Pushback (Kickback, Pinch) Rapid pushback of chain
Nose
saw. Pushback may occur if chain along top of guide bar is
pinched, caught, or contacts a foreign object.
Guide Bar
Rear Handle Handle located at rear of saw body.
Reduced Kickback Guide Bar Guide bar that reduces
Spike
chance of kickback.
Replacement Chain Chain that complies with CSA
Standard Z62.3 when used with a specific saw. It may not meet
CSA requirements when used with other saws.
Saw Chain (Chain) Loop of chain having cutting teeth for
cutting wood. The motor drives chain. The guide bar supports
chain.
Spiked Bumper (Spike) Pointed teeth at front of saw body
beside guide bar. Keep spiked bumper in contact with wood
Oil Cap
when felling or bucking. It helps maintain position of saw
while cutting.
Switch
Sprocket Toothed wheel that drives chain.
Lockout
Switch Device that completes or interrupts electrical circuit
to motor of saw.
Switch Linkage This device connects switch to trigger. It
moves switch when you squeeze trigger.
Switch Lockout Device that reduces accidental starting of
saw.
Trigger Device that turns saw on and off. Squeezing trigger
turns saw on. Releasing trigger turns saw off.
Trimming (Pruning) Process of cutting limb(s) from a
living tree.
Undercut An upward cut from underside of log or limb. This
Trigger
is done while in normal cutting position and cutting with top of
guide bar.
UNPACKING
1.
2.
FILLING OIL TANK
1. Remove oil cap.
2. Fill oil tank with SAE #30 motor oil. Note: For tempera-
3. Replace oil cap at once. Tighten oil cap firmly for good
4. Wipe off excess oil.
Note: It is normal for oil to seep when saw is not in use.
Empty oil tank , tighten oil cap, and store upside down after
each use to prevent seepage.
5
Remove all items from carton.
Check all items for any shipping damage. If you find any
damage or if any parts are missing, promptly inform
dealer where you bought chain saw.
tures below -1°C, use SAE #10 oil. For temperatures above
24°C, use SAE #40 oil.
seal. This will avoid oil seepage from tank.
5
Publicité
