Black & Decker KW1600E Traduction Des Instructions D'origine page 10

ENGLISH
Use
Warning! Let the tool work at its own pace. Do not overload.
Carefully guide the cable in order to avoid accidentally
u
cutting it.
Adjusting the depth of cut (fig. I, J & K)
The depth of cut is the distance X between the depth stop bar
(9) and the depth stop (29). The depth of cut can be set in two
different ways as described below.
Adjusting the depth of cut using the scale (fig. J)
Fit the router bit as described above.
u
Loosen the locking screw (30).
u
Pull the plunge lock lever (5) up.
u
Plunge the router down until the router bit touches the
u
workpiece.
Push the plunge lock lever (5) down.
u
Move the depth stop bar (9) down against the depth stop
u
using the depth stop adjuster (31). Reset the scale by
aligning the zero marking (32) with the arrow (33).
Move the depth stop bar (9) to the calculated position
u
using the depth stop adjuster (31). One quarter turn
corresponds to approx. 6.25 mm.
Tighten the locking screw (30).
u
Fine adjust using the adjusting knob (34). One full turn
u
corresponds to approx. 1 mm.
Pull the plunge lock lever (5) up and return the router to its
u
original position.
After switching the router on, plunge it down and make the
u
desired cut.
Adjusting the depth of cut using a piece of wood (fig. K)
Fit the router bit and plunge the router down as described
u
above.
Loosen the locking screw (30).
u
Move the depth stop bar (9) up using the depth stop
u
adjuster (31).
Place a piece of wood with a thickness equal to the
u
desired depth of cut between the depth stop (29) and the
depth stop bar (9).
Move the depth stop bar (9) down against the wood using
u
the depth stop adjuster (31).
Tighten the locking screw (30).
u
Fine adjust using the adjusting knob (34).
u
Remove the piece of wood.
u
Pull the plunge lock lever (5) up and return the router to its
u
original position.
After switching the router on, plunge it down and make the
u
desired cut.
Adjusting the revolver depth stop (fig. L)
After turning the revolver depth stop to the desired setting, you
can fine-adjust the depth stop to be used. If you want to make
10
several cuts with a different depth of cut, adjust each of the
depth stops.
Turn the depth stop screw (35) up or down as required
u
using a screwdriver.
Setting the speed
Set the speed control knob (4) to the required speed.
u
Use a high speed for small diameter router bits. Use a low
speed for large diameter router bits.
Using a batten as a guide (fig. M)
When it is not possible to use the edge guide, for example
when routing grooves in the back panel of a bookcase to
support shelves, proceed as follows:
Select a piece of wood with a straight edge to use as a
u
batten.
Place the batten onto the workpiece.
u
Move the batten until it is in the correct position to guide
u
the tool.
Securely clamp the batten to the workpiece.
u
Using the template guide (fig. D)
The template guide can be used to make a cutout shape from
a template, for instance a letter.
Secure the template over the workpiece with double-sided
u
tape or 'G' clamps.
The router bit must extend below the flange of the
u
template guide, to cut the workpiece in the shape of the
template.
Using the distance piece (fig. E)
The distance piece can be used for trimming wooden or
laminate vertical projections.
Using the centring pin (fig. F)
The centring pin can be used to cut out circular patterns.
Drill a hole for the point of the centring pin in the centre of
u
the circle to be cut.
Place the router on the workpiece with the point of the
u
centring pin in the drilled hole.
Adjust the radius of the circle with the bars of the edge
u
guide.
The router can now be moved over the workpiece to cut
u
out the circle.
Using the copy follower (fig. G)
The copy follower helps to maintain an equal cutting distance
along the edge of irregularly shaped workpieces.
Place the router on the workpiece at the desired distance
u
from the edge to be copied.
Adjust the bars of the edge guide until the wheel is in
u
contact with the workpiece.