Publicité
Les langues disponibles
Les langues disponibles
PREPARATION
"
Build solid framing to the dimensions in Figure 1.
"
Ensure that the floor is level, shim unit if necessary.
"
The drain location on the shower is shown in figure 1.
"
Drain pipe must be vertical.
"
Trim drain pipe as required to meet drain assembly.
"
Place the unit into position and plumb vertical, shim if
necessary.
"
Dry fit drain to check position.
"
Mark and drill 3/16" pilot holes for plumbing fixtures.
"
Verify that the holes are in the right location.
"
From the finished side of the unit use the correct size
hole saw to cut the openings, using the pilot holes as
guides.
INSTALLATION
"
Carefully position the Shower into the framing and
push flush against the framework walls.
"
Install the drain according to the manufacturer's
instructions. Use a mildew resistant silicone bathroom
caulking to seal the drain to the top surface of the
shower.
"
Fasten the acrylic unit to the framing using drywall
screws. Countersink for screw head flush fit on the
acrylic flange. Please note to make sure that the unit is
plumbed before fastening.
"
Apply silicone caulking over the head of the screws
and around the openings for the fittings when they are
installed.
TESTING
Test the installation after completing the plumbing, but
before enclosing the base and finishing the surroundings.
Run water for 15 minutes to ensure that there are no leaks
at the drain.
Mirolin Industries Corp. will not be liable for any kind of
damages as a result of not water testing the unit prior to
use by end user.
FINISHING
Apply trim around the shower base periphery to finish
!
drywall, if required.
Install Shower Door according to the manufacturer's
!
instructions if purchased
We want you to be completely satisfied with our products and service. If you have any comments or suggestions, please call
The company reserves the right to change models and specifications without notice.
60 Shorncliffe Rd., Toronto, Ontario M8Z 5K1
Telephone: 416.231.9030
800.MIROLIN(647-6546) toll free.
Fax: 416.231.0929
www.mirolin.com
Mirolin Industries Corp. is not responsible for any
damages incurred as a result of poor installation of the
product.
TROUBLESHOOTING
"
The lower part of shower is not level: Refer to
shimming section on page 1.
"
Water remains around the drain: Check that the
installation is level and that the unit sits firmly on its
base; use wood shim to correct.
INSTALLATION CLEAN-UP
Remove construction dirt and residue with a mild liquid
detergent. DO NOT USE abrasive cleaners, scouring
compounds and pads, metal scrapers, steel wool, or other
materials that could damage or dull the surface of the unit.
Remove plaster carefully with a blunt wooden block
having rounded edges.
Remove paint and other stubborn stains with isopropyl
(rubbing) alcohol.
DO NOT USE products such as acetone (nail polish
remover), dry cleaning solution, lacquer thinners,
gasoline, pine oil, etc.
MAINTENANCE
The acrylic sheet, which forms the surface of your
bathtub, provides one of the most durable surfaces found
in modern bathrooms. Keep it bright and smooth with mild
liquid household detergent, soap and water, or foaming
cleansers. NEVER USE aromatic solvents, abrasive
cleaners, scouring compounds or pads, strong liquid
cleansers, or other material that could damage or dull the
surface of the shower.
Restoring Surface Gloss - Restore surface gloss by
applying a very fine rubbing compound and polishing the
surface by hand or with a power buffer. Finish with an
application of a good quality automotive wax.
Minor Repairs to Surface - Remove minor scratches
and scuffs as follows. First, wet sand the area with 600 grit
wet sandpaper until the surface is smooth. Then, restore
the gloss as described under RESTORING SURFACE
GLOSS.
Customer Service: 416.231.5790
Canada, U.S.A.: 800.MIROLIN(647-6546)
Fax, Canada: 800.463.2236
C
US
R0084303
3
28 Feb. 19
Publicité
