Publicité
5.6 Line guide (Fig. 7 / Item 6)
Using the line guide (6) you can carry out exact
cuts following cutting lines marked on the workpi-
ece. Use the mark (a) for the 0° angle setting (Fig.
7) and the mark (b) for the 45° angle setting.
See point 5.4 for information about the angle
setting.
Caution! Carry out trial cuts on a piece of waste
wood.
5.7 Splinter guard (Fig. 8 / Item 17)
The splinter guard ensures that the material you
want to cut does not splinter or crack during sa-
wing.
Important! The splinter guard can be used only
for 0° cuts and must be removed for miter cuts up
to 45°!
To fi t the splinter guard you must press it into the
opening provided on the bottom side of the sole-
plate (7); to detach it, proceed in reverse order.
5.8 Charging the Li battery pack (Fig. 10-11)
1. Remove the battery pack (d) from the handle,
pressing the pushlock button (c) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(e) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
Anl_KX_SS_18_Li_SPK13.indb 21
Anl_KX_SS_18_Li_SPK13.indb 21
GB
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.9 Battery capacity indicator (Fig. 10 /Item f)
Press the button for the battery capacity indicator
(g). The battery capacity indicator (f) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6. Operation
6.1 On/Off switch (Fig. 12/Item 3)
Switching on:
Press the locking button for the On/Off switch (2)
fi rst and then press the On/Off switch (3).
Infi nitely variable stroke speed control is possible
with the On/Off switch (3). The further you push
the switch, the higher the stroke speed.
Switching off :
Release the locking button for the On/Off switch
(2) and the ON/OFF switch (3).
- 21 -
13.01.2022 10:09:47
13.01.2022 10:09:47
Publicité
