Stadler Form Kettle Two Mode D'emploi page 7

4. To boil the water just push the ON/OFF button, a short buzzer sounds and
the water boiling starts.
• When the temperature is below 40 °C, there is "0" on the display,
when the temperature is above 40 °C the current water temperature
will be displayed.
• The water boiling time is approx. 3 minutes.
5. As soon as water has come to a boil, 5 short buzzer sounds and the kettle
will switches off automatically.
6. To switch the kettle off before it switches automatically just push the
ON/OFF button.
7. Ensure that the kettle is switched off before removing it from base.
NOTE
When the kettle switched off automatically you can use it again after 15-
20 seconds..
Water heating temperature setting
• Water heating temperature setting is allowed in stand-by mode only.
• To set the water heating temperature push the temperature up and down
buttons «+»/«–».
• Pushing these buttons you can set the water heating temperature 50, 60,
70, 80 or 90 °C, and the relevant temperature values will be displayed.
• Having chosen the desired temperature push the ON/OFF button, a buzzer
sounds, the button LED lights on and the heating process starts.
• When water reaches the set temperature the kettle will switches off au-
tomatically and LED lights off.
Boiling and subsequent keep warm mode
• Push keep warm button; a buzzer sounds and the button LED lights on.
• Set the desired temperature pushing the keep warm button.
• Push ON/OFF button to boil water. As soon as water has come to a boil
the kettle switches off automatically; and the keep warm mode is on for
30 minutes. After this time the kettle switches off automatically and a
buzzer sounds.
Water heating to a set temperature and subsequent
keep warm mode
• Set the desired temperature pushing the temperature up and down but-
tons «+»/«–».
• Push the keep warm button; a buzzer sounds and the button LED lights on.
• Push ON/OFF button to heat water to a set temperature.
• When water reaches the set temperature the keep warm mode is auto-
matically on for 30 minutes. After this time the kettle switches off auto-
matically and a buzzer sounds.
• Default temperature setting is 50 °С. If you do not set the temperature,
after heating the default temperature setting will be maintained.
All manuals and user guides at all-guides.com
NOTE
Follow the setting sequence as described in the user's manual. If breaking
the sequence you will not be able to set the kettle properly.
When ON/OFF button was pushed all other buttons are not active.
When the keep warm mode button was pushed the heating temperature
cannot be set as the temperature up and down buttons «+»/«–» are not
active.
CARE AND CLEANING
• Remove the plug from the wall socket and let the appliance cool down
before cleaning.
• To clean the filter, remove it and rinse it under hot running water, using a
nylon brush. After cleaning, install the filter in place.
• Use a soft moist tissue cloth to clean the exterior of the kettle and then
rub dry.
WARNING!
Never immerse the kettle, the base unit as well as mains cord and the plug
in water or any other liquid.
Descale Your Kettle Regularly
Mineral deposits in tap water solidify when the water is heated; lime scale
may be white, coloured, even rusty-looking and is normally visible but phos-
phate scale isn't generally visible although may cause the water to appear
cloudy when heated. This may cause the interior of the water gauge to dis-
colour, cause overheating, trigger the boil-dry cut-out mechanism or even
reduce the kettle's life.
Even in soft water areas it is important to descale your kettle regularly to
help maintains its lifecyle.
1. Fill the kettle with 3 cups of white vinegar and the remainder with water
and allow to stand overnight. DO NOT BOIL.
2. Empty the solution from the kettle. Any stains remaining inside the spout
can be removed by rubbing with a damp cloth. Fill the kettle with clean
water, bring to boil and then discard the water. Repeat and the kettle will
then be ready to use.
REPAIRS AND TROUBLESHOOTING
• For safety any repairs of the appliance should be carried out by qualified
personnel of an authorised service centre.
• The warranty does not cover faults caused by unqualified repairs or incor-
rect operation of the appliance.
• It is prohibited to use the appliance when it is faulty, or when the appli-
ance itself, the wire and its plug have been mechanically or otherwise
damaged.