Publicité
2
MOUNTING THE HOT AND COLD VALVES
A. Each faucet is supplied with a hot
and cold valve .Make sure you mount
hot (15) on the LH and cold (19) on
the RH
B. Take the hot valve (15) and mount
the tight fitting nut (18) halfway down
valve body with 2 little screws down.
Follow with the metal washer (17) and
the rubber washer (16). Push through
the under side and secure with flange
anchoring nut (22). You have set the
proper valve height when this anchor-
ing nut is completely threaded. Now
you can secure valve tightly with the
both added screws ( 20).
C. Do the same on cold valve(19).
Make sure your valve outlets are
directed toward the spout.
4
CONNECTING THE
FLEXIBLE HOSES
A. Insert the rubber washers in the1/2" female and 3/4 " female nuts
at the end of the flexible hoses.
B. Connect the flexible hoses (60) to the hot (15) and cold 1/2 "
valve (19) and the 3/4" end to the T section. Secure firmly without
twisting the hoses.
C. Before connecting the extension hose to the hand
shower(30),mount the check valve (61) onto the bottom of the deck
spout. Note that the female end of the check valve has the washer
factory sealed in place already. Tighten firmly. Now take the exten-
sion hose (63) and mount the 3/8"male end of the hose into the
female end of the chrome deck hose (32) sealing this with rubber
washer. Tighten firmly. Finally mount the female end of the exten-
sion hose (63) with rubber
washer(62) onto the male end
of the check valve (61).
Tighten firmly.
15
60
T
Products info: www.aquabrass.com
last revision: 05/21/2013
XCHANGE
22
HOT
16
17
18
15
61
62
63
3
MOUNTING THE HAND SHOWER
A. Insert the flange and his threaded
tube through the outside hole of the deck
COLD
(L or R). From the bottom, mount the
rubber washer (34) and then the metal
washer (35) on the threaded tie down
tube and thread all those with the tight fit-
ting nut (36). Secure firmly the spout with
the both added screws (37).
20
19
B. Now put together the chrome flexible
hose (32) and the hand shower (30).
Tighten firmly.
C. Now slide the flexible hose with hand
shower attached through the top of the
holder.
5
MOUNTING THE HANDLES
A First of all, mount the handles (28)
on their flanges (3). Put the first fiber
washer (26) on the threaded part of the
jointed hexagonal nut (23). Put this
special nut through the flange hole.
Over this, put the second fiber washer
(26) and thread all those parts together
under the handle. Tighten firmly the
nut with the special hexagonal key.
B. Make sure that the large O ring (7)
is well inserted in the groove under the
flange.
C. Mount the handles and the flanges
(27) in the desired position on the car-
30
tridge broach (15), (19). Secure with
the setscrew (4).
D. Check the quarter turn movement of
each handle and verify the position and
that each handle is in good working
32
order
xsquare X7818
4-piece deckmount tub filler with handshower
Deckmount 4 pc tub set
robinet de bain 4 morceaux avec douchette
ON THE VALVES
3
22
HOT
IN-XCH18-2-E
30
32
33
34
35
36
37
28
4
26
7
23
27
COLD
19
15
Updated 30-06-05
aquabrass.com
Publicité
