SALKI 86900080 Notice D'instructions page 10

PNEUMATIC TAKER
TECHNICAL DATA
Staple/nail
Model Staple type
86900080 80 staple
86909050 90 staple + Brad AX
86900006 0.6 pin
86900050 Brad AX
IMPORTANT SAFETY RULES
• Users of this equipment should read this manual carefully and ensure that they understand the explanations provided prior to using the equipment.
• Failure to follow instructions may result in serious injury to the user and/or damage to the equipment.
• The employer is responsible for enforcing the use of personal protective equipment and applying equipment safety measures recommended
for the user and other personnel in the workplace.
• This device is NOT a toy. It contains staples and nails. Children should be kept away from work area and should never operate the device.
• Wear safety glasses and hearing protection to prevent damage during loading, unloading and use of the equipment.
• Before starting work, make sure you have a clean and well-lit work area to avoid possible accidents.
• Never use oxygen, carbon dioxide, or other combustible gas cylinders as a power source as this will cause an explosion and serious damage.
• Never use high pressure with these devices.
• Do not connect the tool to the compressor when the pressure is greater than the maximum working pressure.
• Only use the consumables (staples/nails) recommended in the technical data sheets for each device.
• Make sure the air hose is properly secured or positioned to prevent injury, damage or tripping.
• Make sure all connections are properly secured.
• Carry the tool by the handle only in order to prevent pressing the trigger and accidental firing.
• To prevent injury, do not point the tool at yourself or any other person.
• Disconnect the tool from the compressed air supply when:
• Performing any maintenance, cleaning work, transfer or removal from the work area, or when handing the tool to another user.
• Loading recommended consumables
• To prevent accidental firing do not hold the trigger or safety down when loading consumables.
• These devices are specifically designed for use on non-metallic surfaces, upholstery, plated materials, elastic belts etc.
• Do not use on scaffolding, ladders or similar metal structures. Do not use in sealed or air-tight locations or in vehicles. Never use the tool on
hard or brittle materials such as concrete, steel or tiles. Do not use the device near the edge of a workpiece or near the edge of the work surface,
as the staples may shoot out.
• Never use the tool if it has an air leak, with missing or damaged components, or when in need of repair. Make sure all screws have been
properly tightened.
• Never make unauthorized modifications to the tool.
• Inspect the trigger and safety regularly to ensure that the tool works properly.
• The tool and the air hose must have a pressure release coupling to vent excess pressure when the device is disconnected.
• Grupodesa Fasteners, S.A.U. is not responsible for malfunction resulting from modification of the product by the user not authorized by the
manufacturer/distributor.
INSTRUCTION MANUAL
Model
86900080
86909050
86900006
86900050
• Only use the consumables (staples/nails) indicated for each of the devices listed in the technical data section of this manual.
HOW TO LOAD CONSUMABLES:
ATTENTION! Keep the tip of the tool away from your body and other people when loading consumables. Disconnect the air hose prior
to loading. Make sure the trigger is not pressed when loading the device.
• SIDE LOADING: Press the latch to open the cover, load the consumable, and then close the cover.
• BOTTOM LOADING: Press the magazine down to the rear of the loader and secure the locking mechanism. Load the consumable and release
the magazine mechanism.
• Make sure the nails/staples are properly positioned.
• The tool is now ready to use.
GENERAL INSTRUCTION MANUAL:
• ACTIVATION AND FIRING SYSTEMS
- DEVICES WITHOUT CONTACT SAFETY:
- INDIVIDUAL ACTIVATION: The trigger must be activated for each nailing operation.
- SINGLE ACTIVATION WITH BASIC SAFETY: The safety is built into the trigger to prevent firing when the the tool is not in use.
- DEVICES WITH CONTACT SAFETY:
- DUAL ACTION SAFETY/CONTACT SAFETY: The contact safety and trigger system must be activated to fire the staple. Just press and hold
the trigger and activate the contact safety system to fire the nail/staple. The device fires at a high speed (the catch release triggers firing).-
- Connect the tool to the air supply and make sure the air pressure is in accordance with the indications of the technical specifications
for the device you are using.
- The nail driving depth should be tested using a piece of wood before use. If necessary, driving depth can be regulated using the
Staple/nail length
capacity
140 un. 6-16 mm (1/4"-5/8")
100 un. 13-32 mm / 10-32 mm
100 un. 10-35 mm
100 un. 10-50 mm
Type of safety
Basic safety
Contact safety
Basic safety
Contact safety
Gauge Pressure
Ga21 (0.9x0.7 mm) 4-6 bar (60-90 psi)
Ga18 (1.05x1.25 mm) 4-7 bar (60-110 psi)
Ga23 (0.64 mm) 4-7 bar (60-110 psi)
Ga18 (1.05x1.25 mm) 4-8 bar (60-120 psi)
Type of loading
Bottom
Bottom
Side
Side
10
Maximum Device
Air inlet
pressure dimensions
8 bar 1/4" N.P.T. 47x147x205 mm 0.87 Kg
8 bar 1/4" N.P.T. 50x200x255 mm 1.25 kg
8 bar 1/4" N.P.T. 45x180x220 mm 1.02 kg
8 bar 1/4" N.P.T. 60x230x255 mm 1.22 kg
360° air regulator
No
Yes
No
No
| EN
Weight