Edesa ECB-7411 X Manuel D'instructions page 13

with the essential requirements for low-
voltage electrical equipment, as set out in
Directive 2014/35/EU, and electromagnetic
compatibility, as set out in Directive 2014/30/
EU.
- Shall not be held responsible for failure to
follow the instructions given in this manual
or non-compliance with safety standards
relating to the correct use of the equipment.
- Shall not be held responsible for any
damage caused by the incorrect installation,
use or maintenance of the appliance.
- Reserves the right to make any changes to
the equipment or this manual without giving
prior notice.
Should you need technical assistance or
additional information about our products,
please contact your distributor or an official,
authorised technical service.
Hood installation on walls (Fig.1, Fig.2, Fig.3)
Notes: The figures mentioned in this manual are in the first
pages.
If the height from the Hob to the hood in the instruction user
manual of the hob supplier is higher than the hood template,
follow adhere to the hob supplier info.
For gas cooking appliances only: the minimum distance to the
hood must be at least 65 cm.
The screws and bolts supplied for attaching the hood to the wall
are for solid masonry walls. For other types of wall, the suitable
means should be used.
Use a rigid PVC pipe with a min. Ø l20 mm to evacuate fumes
outside.
It is recommended that there are no bends in the outlet tube,
and that there is a distance of less than 1 metre between the
hood outlet and the bend.
The above restrictions do not apply to hoods with no fumes
outlet to outside (recirculation system with activated charcoal
filter). (fig. 7)
Use of the hood - Control panel (Fig.4)
The different control panels are described below. Check the
panel model installed on your hood and see the figure indicated
in each case.
Panel with electronic button (Fig. P1)
1- Lighting on and off.
2- Lighting operating control pilot light.
3- Extractor fan speed - button: speed 1, 2 and 3 Press the
current speed
again to switch off the extractor fan. In panels with TURBO (I I
I i) button,
Turbo speed only will work during 5 minutes, once it runs out,
the speed will
decrease to 2nd speed.
4- Extractor fan operating speed control pilot light.
Timer: keep the chosen speed button pressed down for two
seconds until the
display fashes. The extractor fan works for 5 min. at the current
speed and
another 5 min. at each of the lower speeds until it stops and
the lighting
switches off.
To cancel the timer: press the chosen speed button once.
Five-button panel (Fig. P2)
1- Extractor fan operating control pilot light.
2- Lighting on and off.
3- Extractor fan off.
4- Extractor fan speed - button: speed 1, 2 and 3,
Touch panel (Fig. P3)
1- Filter clean warning display/button. Warning of the need to
replace the
filter – press to deactivate once the filter has been cleaned or
replaced.
2- Enable and disable extractor fan timer.
3- Lighting on and off. Keep pressed down to adjust the lighting
intensity.
4- Extractor fan on and off.
5- Extractor fan speed - button: speed 1, 2 and 3/4. In panels
with TURBO (T)
button, Turbo speed only will work during 5 minutes, once it
runs out, the
speed will decrease to 3rd speed.
Timer: the extractor fan works for 5 min. at the current speed
and another 5
min. at each of the lower speeds until it stops.
Sliding touch panel (Fig. P4)
1- Extractor fan on and off.
2- Sliding touch panel for extractor fan speed control. Also used
in combination
with button -3-. In panels with TURBO (i) button, Turbo speed
only will work
during 5 minutes, once it runs out, the speed will decrease to
9th speed.
3- Lighting on and off. Press the button and, while it is flashing,
adjust the
lighting intensity using the sliding touch panel -2-.
4- Enable and disable extractor fan timer.
5- Filter clean warning display/button. Warning of the need to
replace the
filter – press to deactivate once the filter has been cleaned or
replaced.
Timer: the extractor fan works for 2 min. at the current speed
and another 2 min.