Publicité
AMD AM2(+) / AM3(+) / AM4 / FM1 / FM2(+)
Général
Nous recommandons de monter le radiateur à l'extérieur du
boîtier du PC.
Pour ce faire, vous aurez besoin des pièces suivantes:
1x Ventirad Pure Rock (1), 1x ventilateur 120mm (2), 2x
Supports longs de montage AMD (5), 1x Support de montage
du refroidisseur (6), 4x écrous-entretoises AMD (9), 2x Vis de
fixation du support de montage (11), 4x Vis pour plaque arrière
AMD (13), 2x Clips de fixation (15), 4x Rondelles AM3 (16)
Assemblage du cadre de montage du refroidisseur
Pour permettre le montage du refroidisseur, veuillez retirer
les deux dispositifs de retenue en plastique du module de
rétention AMD. La plaque arrière montée en usine fixée à
l'arrière de la carte mère sera nécessaire pour l'installation
ultérieure du refroidisseur.
Remarque: Pour installer le Pure Rock (1) sur une carte mère
AM3, veuillez utiliser les rondelles AM3 (16), en les plaçant sur
les boulons de la plaque arrière qui dépassent de l'avant de la
carte mère.
AM2(+) / AM3(+) / FM1 / FM2(+)
AM4
Placer les écrous-entretoises 4x AMD (9) sur les boulons de
la plaque arrière sur le côté avant et fixer les deux supports
courts de montage AMD (5) avec les vis pour la plaque
arrière AMD (13).
Le revêtement de protection sur le dessous du refroidisseur
doit être retiré avant l'installation contre le ventirad.
Attention: La pâte thermique fournie n'est pas adaptée à la
consommation humaine. En cas d'ingestion, boire beaucoup
d'eau et consulter un médecin de toute urgence. Gardez-le
hors de la portée des enfants. Eviter le contact avec la peau et
les yeux.
Notes
Montage du refroidisseur du ventirad
Positionnez le support de montage du refroidisseur (6) au
centre du ventirad. Puis, placez le refroidisseur (1) sur le
processeur. Insérer les vis de fixation du support de montage
(11) par le haut dans le support de montage du refroidisseur,
puis vissez les alternativement. Vous pouvez utiliser le
tournevis cruciforme pour cela.
Fixez le ventilateur 120mm (2) sur l'unité de refroidissement (1)
en utilisant les clips de fixation (15). Connectez le ventilateur
au signal PWM de la carte mère.
Lors du démontage le ventilateur 120mm (2), repoussez les
encoches des clips de fixation (15) du ventilateur.
Limited Warranty
As per the terms and conditions of this limited warranty as given
below, be quiet! warrants its new products to be free of defects
resulting from faulty materials and faulty manufacturing for the length
of the warranty period.
I. APPLICABILITY
This non-transferable warranty is applicable to newly purchased,
previously unopened be quiet! products and is enforceable by only
the original consumer purchaser. Proof of purchase is required for
warranty service, so should be retained. be quiet! does not provide
warranty registration services.
II. WARRANTY PERIOD
For eligible products, parts and labor are warranted for the appli-
cable warranty period from the date of purchase. The applicable
warranty period varies by product model, and is identified in your
user documentation, on the product package, or as listed below.
Should any of these warranty periods differ, the longest specified
warranty period will apply. Replaced products will be warranted
for the remainder of the original warranty period or thirty days,
whichever is longer.
III. EXCLUSIONS
The following are not covered by the warranty:
1. Normal wear and tear.
2. Any product which has been modified without permission from
be quiet!, or on which the serial number or warranty sticker has been
defaced, modified, or removed.
3. Damage, deterioration or malfunction resulting from:
Accident, abuse, misuse or improper use, neglect, connection to
an improper voltage source, unauthorized product modification, or
failure to follow instructions included with the product.
Fire, water, lightning, or other acts of nature.
Repair or attempted repair by anyone not authorized by be quiet!.
Shipping or transport damage (claims must be made with the carrier).
Any other cause which does not relate to a defect in materials or
manufacturing workmanship.
4. Cartons, cases, batteries, cabinets, tapes, accessories or other
consumables used with this product.
5. be quiet!, Inc. does not warrant that this product will meet your
requirements. It is your responsibility to determine the suitability of
this product for your purpose.
6. Removal or installation charges.
7. Shipping charges.
8. Any incidental charges.
IV. EXCLUSION OF DAMAGES
be quiet!'s sole obligation and liability under this warranty is limited
to the repair or replacement of a defective product at its option.
be quiet! shall not, in any event, be liable for any special, incidental,
indirect, or consequential damages whatsoever, including but not
limited to loss of profits, revenue, or data (whether direct or indirect),
damages resulting from interruption of service and loss of business,
or for liability in tort relating to this product or resulting from its use
or possession, even if be quiet! has been advised previously of the
possibility of such damages.
V. LIMITATIONS OF IMPLIED WARRANTIES
There are no other warranties, expressed or implied, including but not
limited to those of merchantability or fitness for a particular purpose.
The duration of implied warranties is limited to the warranty length
specified in Paragraph II.50
VI. LOCAL LAW AND YOUR WARRANTY
This warranty gives you specific legal rights. You may also have other
rights granted under local law. These rights may vary.
VII. NO OTHER WARRANTY
No be quiet! employee, dealer, or other agent is authorized to make
any modification, extension, or addition to this warranty.
VIII. TO OBTAIN TECHNICAL SUPPORT OR WARRANTY SERVICE
Please see your product owner's manual or visit the service section
at www.bequiet.com for details and contact information. You will
need to provide proof of purchase for warranty service.
bequiet.com
bequiet.com
Publicité
